A printer that does not pick up paper usually has a dirty or worn pickup roller, a paper problem or a tray problem. The fix is often as simple as fanning the paper and cleaning the rollers. This guide goes through the causes from the easiest to the more involved.
Steps are general; check your manual for access panels and roller locations.
By the Reviewstook Editorial Team. Last updated: October 31, 2026.

Check the Paper First
- Quality and weight: use paper that matches the printer’s specifications. Very thick, glossy or heavily textured paper can fail to feed.
- Curl and moisture: humid paper curls and sticks. Use a fresh ream stored flat and dry.
- Fan the stack: fan the sheets to separate them, then tap the stack on a table to align the edges.
- Do not overload: fill the tray below the maximum line.
In this guide
Check the Tray and Guides
Slide the paper guides so that they touch the stack lightly, not tightly. Make sure the tray is fully seated and the paper sits flat. If your printer has a rear feed, make sure it is not blocked.
Clear Any Jammed Paper
Small scraps can hide in the paper path and stop feeding. Turn off the printer, open all access doors and remove any paper or torn pieces. See how to fix a paper jam.
Clean the Pickup Rollers
Dust and paper residue reduce grip. With the printer off and unplugged, locate the rollers as shown in your manual. Dampen a lint-free cloth lightly with water, wipe the rollers and let them dry fully. Rotate each roller gently to clean the whole surface. Do not use alcohol or harsh cleaners unless the manual allows them.
Check the Paper Type and Size Settings
If the printer expects a different paper size or type than you loaded, it may refuse to feed or ask for paper. Match the settings in the driver and on the printer’s screen.
Worn Rollers
Old rollers become smooth and lose grip. Some printers allow you to replace the pickup roller kit. Check the maker’s parts list. If the printer is old, a replacement may cost nearly as much as a new printer.
Software and Sensor Issues
Restart the printer. If the printer reports “out of paper” when the tray is full, a sensor may be stuck. Check for debris around the sensor and run a printer reset; see how to reset a printer to factory settings.
Prevent Pickup Problems
- Store paper flat, sealed and dry.
- Do not mix old and new paper in the tray.
- Clean the rollers every few months.
- Use the correct paper for envelopes and labels; see how to print envelopes and how to print on cardstock.
How Paper Feeding Works and Why It Fails
Understanding the feed path makes the problem easier to diagnose. When a job starts, the printer lowers or engages a pickup roller that rests on the top sheet of the stack. The roller turns, using friction to slide the top sheet forward. A separation mechanism, such as a pad or a second roller, holds back the sheets below. The sheet then travels through feed rollers to the print area. A failure at any of these steps appears as no pickup, multiple sheets pulled together or a sheet that stops partway.
Each symptom points to a different cause. If nothing moves and you hear no roller turning, the printer may not have received the job, may be showing an error, or a sensor may think there is no paper. If the roller spins but the paper does not move, the roller is slick, dirty or worn, or the paper is too smooth or too heavy. If the printer takes several sheets at once, the paper may be sticking together from static or humidity, or the separation pad is worn. If a sheet is picked up but stops, there may be a jam, a blocked path or a misaligned guide.
Listen and watch when you try to print. Open the tray and look at the roller. Check for error messages on the display or computer. Note whether the problem happens with every paper type or only some, and whether it started suddenly or got worse slowly. A sudden change after you moved the printer, loaded different paper or cleared a jam points to something specific. A gradual decline over months usually points to roller wear or dust. This quick observation can save you from replacing parts that are fine.
Special Media: Envelopes, Labels and Card
Printers are designed around ordinary office paper, and anything different can fail to feed. Envelopes are thick at the seams and flaps, labels have a backing sheet that can peel and cause jams, and cardstock is stiff and may not bend around the paper path. If your pickup problem happens only with these media, the paper path is probably fine, and the media or the settings need attention.
- Check the specifications: the manual lists supported paper weights, sizes and types. Stay within them.
- Use the right path: many printers have a rear tray or a manual feed slot for thick media, which keeps the paper straighter than the main tray.
- Load a few at a time: feed envelopes, labels or card one sheet or a small number of sheets, rather than filling the tray.
- Set the type: choose the matching media type in the driver, so the printer adjusts feed speed and heat.
- Use fresh labels: do not run a label sheet that has missing labels, because the exposed backing can peel off and stick inside the printer.
Envelopes are best fed with the flap side facing the direction that the manual shows, and pressed flat first to remove air. Heavy card may need a straight path with the back door open. Do not use glossy photo paper in laser printers unless it is stated to be suitable, as the heat can melt coatings and damage the fuser. For any special media, test one sheet before running a batch.
Static, Humidity and Storage Effects
The environment affects paper more than most people realize. In dry conditions, static can make sheets cling together, causing several to be picked at once or none to separate. In humid conditions, paper absorbs moisture, curls at the edges and loses stiffness, so the roller cannot grip it cleanly. Both extremes can cause pickup failure, which often appears when seasons change or when paper is kept in a garage, basement or near a window.
Store paper in its original wrapper, flat, and away from heat sources, damp walls and direct sunlight. Keep only as much paper in the printer tray as you will use soon, and put the rest back in its packaging. If the paper has curled, try flipping the stack over, since the curl will then work in the opposite direction, or use fresh paper. If the paper has been in a cold place, allow it to reach room temperature before loading.
Fanning a stack before loading it helps in dry conditions by breaking static contact. Fan it gently and tap the edges level. Avoid loading paper that has been creased or had staples removed from it, because bent edges catch on the rollers. In a very humid room, a dehumidifier or moving the printer to a drier spot may help. If you print on recycled or lightweight paper, check that the maker’s specifications allow it. Many pickup problems are solved by changing the paper brand or weight rather than by touching the printer, so test a fresh, good-quality ream first.
Cleaning and Replacing Rollers Safely
If paper and settings are fine, the rollers are the next suspect. Cleaning is low-risk if done carefully, but follow the manual because the layout differs between models. Turn off the printer and unplug it. Open the access panel or remove the tray as the manual shows. Use a lint-free cloth lightly dampened with water, not dripping, to wipe the roller surface, turning it by hand to clean the whole circumference. Let it dry completely before reassembling. Do not use harsh solvents unless the maker approves them, since they can harden or damage rubber.
If cleaning gives only a short-term fix, the roller may be worn. Signs include a glossy or smooth surface, visible cracks, flat spots or rubber residue on your cloth. Some printers have user-replaceable pickup roller kits, and the maker’s parts list or support page will say whether yours does. Check that the kit matches your exact model number. Follow the replacement steps in the manual, and handle the new roller by its edges to keep skin oils off the surface.
Weigh the cost. If the roller kit is inexpensive and easy to fit, replacing it can extend the life of the printer. If the repair needs a technician or major disassembly, compare the price with a new printer, especially if the printer is old, out of warranty or has other problems. When shopping for a replacement, look for a sturdy paper path, a decent tray capacity, and easy access to the rollers. Check the warranty period and how simple it is to get service, so a feed problem later is easier to resolve.
Settings, Sensors and Firmware Causes
Sometimes the mechanics are fine and the printer refuses to feed because it believes something is wrong. Paper size and type settings that do not match the tray can produce a wait message or an out of paper error. Some printers refuse to print until you confirm the loaded paper on the display. If the printer asks for a paper size you did not choose, check the print dialog and the app’s page setup, since documents set to a different size can trigger the prompt.
Sensors can also give false readings. A small flag or optical sensor detects the presence of paper, and a stuck flag, dust or a scrap of paper can make the printer think the tray is empty or the path is blocked. Open the covers, remove the tray, and look for torn pieces or small objects. Use a soft brush or compressed air carefully, and follow the manual before touching any part.
Software can play a part. A stuck print job in the queue can lock the printer in an error state, so clear the queue and try again. A driver mismatch after an update, or firmware that needs updating, can cause odd behavior. Check the maker’s support page for firmware updates and install them as directed, keeping the printer powered on and connected during the update. If all else fails, try a power cycle: turn the printer off, unplug it for a minute, plug it back in and restart. Reset to factory settings only as a last step, because you will need to set up the network and preferences again.
A Quick Pickup Troubleshooting Checklist
When a printer refuses to grab a sheet, it is easy to jump straight to the worst case. A calm, ordered check usually finds the cause faster. Run through these steps one at a time and try a single page print after each.
- Switch the printer off, unplug it if the manual says to, and remove all paper from the tray.
- Look inside the tray area with a torch for torn corners, staples or small scraps of paper.
- Check that the tray is pushed fully into the printer and clicks into position.
- Load a fresh, flat stack from a new ream, and tap it square before placing it in.
- Set the guides so they touch the stack lightly without bowing the sheets.
- Confirm the paper size in the tray matches the size chosen in the print window.
- Try a different tray, if your model has one, to see whether the fault follows the tray or the printer.
- Print a test page from the printer’s own menu to rule out a computer or software problem.
Write down which step changed anything, since that note helps you or a technician narrow the fault later.
Sizing Up the Paper Itself
Paper is often blamed for pickup trouble, and sometimes that is fair. Every printer manual lists a supported weight range, usually given in grams per square meter, and thicker card or very thin sheets fall outside what the pickup system was built to handle. Look in your manual for the figures and compare them with the label on the ream wrapper.
Condition matters as much as weight. Sheets that have curled in a damp room, stuck together after sitting near a window or picked up creases from a bag will feed poorly. Store paper flat in its wrapper, in a dry cupboard, and keep the tray stocked with only the amount you need for the week.
Mixing paper types in a single stack is another trap. Plain sheets on top of glossy photo paper, or a few old pages added to a new pile, change how the roller grips. Keep one type per load. If you switch media, tell the printer through its menu or the print dialog so it can set the right feed behavior.
Own the Fix or Book a Repair: A Simple Comparison
Some pickup faults are quick household jobs, while others belong with a trained technician. The table below helps you decide where to draw the line.
| Situation | Try yourself | Contact the maker or a technician |
|---|---|---|
| Dusty roller surface | Wipe as the manual describes | If the manual gives no access steps |
| Curled or damp paper | Replace the ream | Not needed |
| Shiny, smooth roller | Check for a roller kit from the maker | If parts are hard to reach |
| Grinding or clicking noise | Clear visible debris | If the noise continues |
| Error code after a jam | Follow the jam steps in the manual | If the code returns |
Always follow the manual before opening any panel. If the printer is under warranty, opening it yourself may affect your cover, so check the terms first and ask the maker’s support team for steps that suit your exact model.
It also helps to keep the printer’s model number, a note of the symptoms and the date the trouble began before you call. Support staff can then tell you whether a known fault exists, whether a replacement roller kit is sold for your machine and whether a service visit makes sense. For older machines, compare the cost of repair with the cost of a replacement unit, and consider how much printing you really do each month before choosing.
Habits That Keep Feeding Smooth
A little routine care cuts down on repeat trouble. Wipe the tray and surrounding area when you refill paper, fan the stack gently before loading, and avoid squeezing more sheets in than the fill line allows. Keep the printer on a firm, level surface away from damp walls, and cover it from dust when it will sit idle for long periods.
Check the paper path after any move, since a printer carried between rooms can pick up debris or have its tray knocked slightly out of line. If you share the machine with a household or office, put a short note near it that explains which paper to load and how to seat the tray. Many repeat jams come from a different person loading a mismatched stack in a hurry. Keep spare, sealed reams close at hand so nobody is tempted to reuse crumpled or half-used sheets. A few minutes of tidy habits each week is usually less costly than a service call, and it keeps your pages coming out clean.


Products Worth a Look
As an Amazon Associate, Reviews Took earns from qualifying purchases. These picks come from our guide: 5 Best Recycled Printer Paper (October 2026).
-
PrintWorks 100% Recycled Printer Paper
-
Amazon Basics 30% Recycled Multipurpose Copy and Print Paper
-
Staples Pastel Recycled Copy Paper
How Paper Pickup Actually Works
Understanding the mechanism turns this fault from mysterious to mechanical. When you print, a pickup roller, usually a rubber roller or a D-shaped roller that rotates once per page, presses against the top sheet of the stack and pushes it forward. A separation pad or a second roller working in opposition holds the rest of the stack back, so exactly one sheet advances into the paper path, where transport rollers take over.
Every failure in this guide is one of those three elements misbehaving. If the pickup roller cannot grip, nothing moves and the printer reports an empty tray or a jam that never happened. If separation fails, several sheets move together and the printer jams or prints on overlapping pages. If the paper itself resists, too stiff, too slick, too damp or loaded badly, both of the other elements are blamed for the paper’s behavior. Diagnosis is deciding which of the three you are looking at.
Listen while the printer tries. A roller spinning against paper it cannot move makes a characteristic repeated attempt sound, often two or three tries before the error. Paper that crumples at the tray entrance has moved and failed. Silence followed by an empty-tray message suggests the printer does not believe paper is present at all, which points at loading, guides or the paper sensor rather than at grip.
The Paper Itself: Loading, Quantity and Condition
Start with the stack, because it is the cheapest suspect and the most common culprit. Remove the paper entirely and inspect it. Sheets should be flat, dry and uniform. A stack that has lived in the tray for months absorbs moisture at its edges, curls and sticks to itself; a fresh stack from a sealed pack behaves like a different material, because it is one.
Fan the stack before loading: hold it by one edge and flex it so air passes between the sheets, breaking the static and surface tension that make sheets travel together or refuse to separate. Square the stack on a flat surface so its edges align, then load it without forcing it past the tray’s capacity marks. Overfilled trays defeat pickup by pressing the stack too hard against the mechanism; nearly empty trays fail too, because some mechanisms need the weight and spring pressure of a reasonable stack to work against.
Set the tray guides to touch the paper’s edges without squeezing. Guides left wide let the stack skew as it feeds, and a skewed sheet meets the path at an angle it cannot survive. Guides cranked tight bow the stack upward. Both errors produce pickup failures that look mechanical and are actually geometric.
Check orientation and type. Some printers expect paper loaded printable-side up, others down, and specialty media often have one correct face. Heavy, glossy or textured stock beyond the tray’s rating belongs in the manual or rear feed if the printer offers one, where the path is straighter and the pickup is designed for awkward media.
Cleaning the Pickup Roller, Step by Step
When fresh, correctly loaded paper still will not feed, the pickup roller’s grip is the next suspect. Rollers accumulate paper dust, which is mostly fine clay and fiber from the paper itself, and their rubber surface gradually glazes. The result is a roller that spins politely on top of the stack and moves nothing.
Find the roller from the manual’s diagram for your model; on many printers it is visible when the tray is removed or through the rear access. With the printer unplugged, clean the roller with a lint-free cloth lightly dampened with plain water. Rotate the roller by hand as the manual allows and clean its whole circumference, because the flat spot or glazed patch may be only part of the surface. Let it dry fully before testing.
Do not use alcohol, solvents or rough materials unless the manual specifically recommends them; they can harden or swell roller rubber and convert a dirty roller into a dead one. If cleaning restores feeding, note the date: rollers need this attention periodically in dusty rooms and heavy use, and a calendar note beats rediscovering the fault each season.
If the roller is visibly cracked, shiny-hard, out of round or has a worn flat area, cleaning has reached its limit. On many home and office models the pickup roller is a user-replaceable part with a part number in the manual; on others it is a service item. Replacing a worn roller on a printer you otherwise like is one of the most cost-effective repairs in all of printing, because it restores the function everything else depends on.
Separation Problems: When One Sheet Becomes Three
The mirror-image fault, several sheets feeding together, points at separation. The separation pad is a small friction surface that holds the lower sheets while the top one advances; when it wears smooth or becomes contaminated, it stops discriminating. Clean it the same gentle way as the roller if the manual shows it as accessible, and check for a torn corner or a label stuck in the tray area adding its own unwanted friction map.
Paper behavior dominates separation too. Damp, static-heavy or freshly printed sheets reused as scrap stick together enthusiastically. If multi-feeds begin in humid weather or with a particular paper stock, change the paper before changing parts. Some printers also offer a setting or a lever for thick or special media that adjusts separation pressure; the manual names it for your model.
Watch for the pattern across trays. A printer that multi-feeds from the main tray but feeds perfectly from the manual slot has localized its own fault to the main tray’s pickup and separation parts. A printer that multi-feeds everywhere is usually describing its paper.
Tray-Specific and Path-Specific Clues
Modern printers offer several ways in: the main tray, a manual or rear feed, sometimes a second tray or an envelope slot. Use them diagnostically. Load the same fresh paper in a different path and print. Success elsewhere proves the printer’s core mechanism healthy and convicts the failing path’s roller, pad or guides.
Rear and manual feeds deserve special mention for difficult media. Their straighter path and different pickup geometry handle thick, stiff and small media that the main tray’s curved path cannot. Envelopes, card and photo paper that refuse the main tray often feed flawlessly from the rear, not because the printer is fixed but because the right tool was used. The manual’s media table says which path each stock prefers; believing it saves rollers and tempers.
Also inspect the failing tray itself. Trays are removable, droppable and crackable, and a tray with a warped floor or a broken spring plate cannot present paper at the angle the pickup expects. Swap trays if the printer has two, or inspect the tray against a flat surface, before condemning parts inside the machine.
When the Printer Insists the Tray Is Empty
A printer that reports no paper with a full tray is usually not lying about its beliefs: a sensor, often a small lever or optical flag in the tray area, tells it whether paper is present, and that sensor can be blocked by a torn scrap, bent by an overfilled tray being forced in, or simply dusty. With the tray removed and the machine unplugged, look into the tray bay with a torch for the sensor and for debris around it.
Loading technique matters here too. Paper pushed too far, or not far enough, can miss the sensor’s position entirely, especially with small media sizes. Confirm the size settings match the paper loaded: a tray configured for a larger size may not register a smaller stack where it expects it. Reload deliberately, guides set, stack seated as the tray’s markings show, and watch whether the printer’s belief changes.
A sensor fault that survives cleaning and careful loading is a service item, but it is a small one, and describing it precisely, “reports empty with paper loaded, all trays, sensor area clean”, gets you a faster resolution than reporting that the printer will not print.
More Questions About Paper Pickup
Why does the printer pick up paper only when I press down on the stack?
Because pressure is compensating for grip or geometry: a worn pickup roller that needs help, a tray spring that has weakened, or guides set so the stack sits slightly wrong. Your hand is acting as the missing mechanism. Clean the roller first; if hand pressure remains necessary, the roller or the tray’s lifting mechanism is worn, and you have diagnosed the repair precisely.
The first page fails but the rest print. What is different about page one?
The top sheet of a resting stack is the one most exposed to dust, moisture and curl, and it is also the sheet the mechanism meets cold. If page one regularly fails and its successors feed, replace the top few sheets with fresh ones and store the loaded tray’s paper better. If the failure is mechanical, a roller with one damaged section can also fail on its first revolution and catch on later ones, which cleaning and inspection will reveal.
Can paper really expire?
Paper does not expire like food, but it absolutely degrades as a printing material. Opened packs absorb moisture, edges curl, coatings age and dust settles. A pack that has sat open in a damp room for a year may feed badly forever, however fine it looks. Fresh paper is the cheapest diagnostic in this entire guide, which is why it appears first in every sequence.
My printer feeds paper crooked and then jams. Is that the same problem?
It is the neighboring problem: pickup succeeded, alignment failed. Crooked feeding points at guides set unevenly, a stack loaded skewed, one roller gripping harder than its partner, or an obstruction on one side of the path. Correct the loading and guides first, clean both rollers evenly, and inspect the path’s entrance for a scrap sitting to one side.
Envelopes, Labels and Other Difficult Passengers
Pickup problems concentrate on media that is not plain rectangular paper. Envelopes feed badly when their flaps catch, when they are loaded in the wrong orientation, or when a stack of them bows under its own uneven thickness. Load envelopes in small quantities, flap position and orientation exactly as the tray’s embossed diagram shows, and use the envelope setting or lever where the printer provides one, because it changes the pressure the mechanism applies.
Label sheets deserve their own warning: a label that peels inside the printer becomes the obstruction that ruins the next month of feeding, and partially used label sheets are the usual source. Feed label sheets from the manual path, one at a time, and retire sheets with missing labels rather than risking the loose one. If pickup problems began right after a label job, inspect the path for a stray label before anything else; it is the classic hidden cause.
Small media, index cards, photo sizes and receipts from a stack, test the guides and the sensor positions. They must be loaded against the correct reference edge, which the tray markings show, and the size settings must match, or the printer looks for paper where the small stack is not. When in doubt, the manual feed with its adjustable guides is the honest route for anything much smaller than standard paper.
A Maintenance Rhythm for Reliable Feeding
Feeding reliability is maintained in minutes per season. Keep paper sealed until it is loaded, and store the opened pack in a dry cupboard rather than on top of the printer where heat and dust reach it. Vacuum or wipe the tray area when you change packs, because the tray collects the dust that the rollers then wear.
Clean the pickup roller when feeding first becomes hesitant, not after it fails outright; hesitation is the early warning the mechanism gives you, and a five-minute clean at that stage prevents the jam-and-error phase entirely. Note cleanings in the same log as cartridge changes, and patterns will emerge: many households discover their roller needs attention on a predictable cycle tied to paper volume or to a dusty season.
Finally, retire paper that has been through the printer once and emerged printed on one side from the scrap stack if your printer struggles with it. Pre-printed sheets are curled, statically charged and dimensionally changed by heat; a fussy feeder is entitled to refuse them, and feeding fresh paper to a machine with a known appetite is cheaper than another evening of troubleshooting.
Does the room’s humidity really change how paper feeds?
Yes, measurably. Paper is a sponge made of wood fiber; it takes on moisture from humid air, growing heavier, limper and stickier, and it dries brittle in heated winter rooms. Both extremes feed worse than the middle. If your pickup problems keep a seasonal calendar, the paper’s storage is the first fix: sealed packs, a dry cupboard and smaller stacks loaded more often.
When you have worked through paper, loading, cleaning and the alternate path, and the tray still will not feed, you have earned a precise conclusion: a worn roller, a tired separation pad, a weak tray spring or a sensor fault, in roughly that order of likelihood. Each is a defined part with a defined remedy, which is a far better position than the one this fault usually creates, a printer vaguely described as broken. Describe the failed tray, the tests you ran and the paper you used when you talk to support, and the conversation will start where your troubleshooting ended instead of where it began.
Why does pickup fail more with the last few sheets in the tray?
Many pickup mechanisms rely partly on the stack’s own weight and the tray’s spring pressure to present the top sheet firmly against the roller. As the stack thins, that presentation weakens, and a roller with any glaze on it loses the contest. Topping the tray up is a legitimate short-term answer; cleaning the roller is the durable one. A printer that only fails on a nearly empty tray is usually describing marginal grip, not a broken sensor or an empty-tray error.
Keep a small reserve of fresh paper from a sealed pack purely for testing. When feeding fails, that reserve separates paper problems from machine problems in a single load, and it prevents the common spiral of cleaning good rollers and adjusting good guides to accommodate bad paper.
That single habit, fresh paper first, is the difference between owners who fix pickup problems in ten minutes and owners who disassemble healthy printers. The mechanism is usually innocent; the stack, the loading or a film of dust on one roller is confessing, if you test in the order this guide sets out.
Work that order calmly and the printer will usually start feeding before you reach the parts list.
And if it does not, you will know exactly which part to ask about, which is the next best outcome troubleshooting can offer.
Precision about a small mechanical fault is what turns a frustrating printer back into an appliance.
That is the goal of every step above.
Test, clean, reload, and only then replace.
Paper first, mechanism second, parts last: keep that order and this fault rarely survives the evening.
Frequently Asked Questions
Why does my printer say out of paper when the tray is full?
Usually dirty or worn rollers, or a misloaded tray.
Can humid paper cause this?
Yes. Use fresh, dry paper.
Can I fix worn rollers myself?
Some models let you replace them. Check the manual.
Does paper type matter?
Yes. Very thick or glossy paper may not feed.
Why does my printer pick up several sheets at once?
Sheets may be sticking from static or humidity, or the separation pad may be worn. Fan the stack, load fresh paper and check the pad if the problem continues.
Can I use a rubber band or tape on the roller to improve grip?
No. This can damage the roller and cause jams. Clean the roller or replace it as the manual describes.
Why does the printer feed from the wrong tray?
The driver or printer setting may point to another tray, or the paper size setting may match that tray. Check the tray selection in the print dialog and on the printer.
Is it safe to clean rollers with alcohol?
Only if the maker says so. Water on a lint-free cloth is the safer default, and some solvents can harden rubber.
How often should I clean the pickup rollers?
A light cleaning every few months is a sensible habit, and sooner if you use dusty paper or notice feeding problems. Check your manual for advice.
Why does the printer say the paper size is wrong?
The loaded size may not match the setting in the driver or on the printer. Match both, and check the paper guides sit lightly against the stack.
Does recycled paper cause pickup problems?
It can if it is lightweight, dusty or uneven. Check the specifications for suitable paper and try a fresh ream of good-quality paper.
Bottom Line
Fan the paper, set the guides, remove jams, clean the rollers and match the paper settings. If feeding still fails, the rollers may be worn. See our printer not printing guide.
Related Reading
- Types of Printers Explained: Inkjet, Laser, Ink Tank and More
- 7 Best Wireless Printers for Home Use
- How to Set Up a Wireless Printer on Mac (Step by Step)
- Printer Won’t Connect to WiFi: 9 Fixes to Try
- 4 Best Heat Transfer Paper for Inkjet Printers (T-Shirts, 2026)
More Printer Guides
- Best Printers for Home Use
- How to Fix a Printer Offline Error
- How to Connect a Printer to WiFi
- Printer Terms Explained



