Skip to content
RESEARCH-BASED GUIDES. PRACTICAL EVERYDAY ADVICE.How we pick products
RTReviewstookA clearer perspective
Printers

Printer Says Out of Ink After a New Cartridge: What to Do

Printer says out of ink after a new cartridge: reseat it, remove the tape, clean the contacts, reset the ink warning and check compatibility.

We may earn a commission from qualifying purchases. How we pick products

Where to buy

Check the latest price, availability and delivery on Amazon. Orders are placed on Amazon. We may earn a commission from qualifying purchases.

Read the full guide ↓

You refilled the cartridge or tank, and the printer still says it is out of ink. This is a common frustration. The printer is not measuring ink directly in most cases: it counts pages or uses a chip, so it does not know you refilled. This guide explains why it happens and how to fix it.

Check the policy of your printer’s maker before you refill, because some warranties and ink programs have rules.

By the Reviewstook Editorial Team. Last updated: October 31, 2026.

Visual summary: Reseat the cartridge; Remove the protective tape; Clean the contacts.
Visual summary of this guide. Read the article for full details and qualifications.

Why the Printer Thinks It Is Empty

  • The chip on the cartridge: many cartridges contain a small chip that stores how much ink is left. When you refill, the chip still says empty.
  • The page counter: some printers estimate ink use by counting dots or pages, not by measuring ink.
  • Air in the line or head: air can stop ink from reaching the nozzles, so the sensor shows empty.
  • Dirty contacts: if the cartridge contacts are dirty, the printer cannot read the chip.
  • Ink programs and locked cartridges: some printers block refilled or third-party cartridges.
In this guide

Fix 1: Reseat the Cartridge and Clean the Contacts

Remove the cartridge, wipe the copper contacts gently with a lint-free cloth and put it back until it clicks. Turn the printer off and on again.

Fix 2: Override or Reset the Ink Warning

Many printers let you continue after a low-ink message: look for an option such as “Continue” or “Ignore” on the printer or in the software. Some printers have a button combination to reset the ink level counter, which your manual describes. Use this only after you have refilled the correct color.

Fix 3: Run a Head Cleaning to Prime the Ink

After refilling, air can block flow. Run one or two cleaning cycles and a nozzle check. See how to clean a printhead.

Fix 4: Use Reset Chips or a New Cartridge

If the chip is the problem, some people use chip resetters, but they are not always compatible. A new cartridge removes the problem. If your printer is an ink tank model, it normally has no chips on the tanks, and you can refill safely as long as you use the right color and fill to the marked level; see how to refill an ink tank printer.

Fix 5: Check for Firmware Restrictions

Some printers update their firmware to block refilled or third-party cartridges. If the printer rejects them, check the maker’s policy. You may need to avoid automatic updates or use genuine cartridges.

Fix 6: Check the Ink Level Display

Open the ink status screen in the printer or the maker’s app. See how to check printer ink levels. Ink level readings are estimates, so a “low” reading does not always mean empty.

Prevent It

  • Consider an ink tank printer if you refill often; see EcoTank printers.
  • Buy cartridges recommended by the maker.
  • Keep the ink away from heat and light.

How Printers Track Ink Levels

To fix an out-of-ink message it helps to know how the printer arrives at it. Most home printers do not weigh or directly measure the ink in a cartridge. They estimate the remaining amount, and the method differs by model. Some count the drops they fire and the pages they print, subtracting from a starting figure. Others read a value stored on the cartridge chip. A few use a sensor that detects when ink has dropped below a point.

This is why the display can disagree with reality. If a counter or chip says empty, topping up the container does not change the stored number. And if the estimate runs low early, the printer may warn you while ink is still left. The level display is a guide, not a precise gauge, as the post notes in the section on checking the display.

The type of printer also matters. A cartridge model with a chip behaves differently from an ink tank model with open reservoirs. Ink tank printers often track usage in the printer rather than on the tank, so the manual may describe a reset step after refilling. Check the manual for your model name and look for sections on ink status, replacing ink or maintenance. If you are not sure which method your printer uses, searching the manual for the words cartridge, tank or level usually points you to the right place.

Refilled Versus New Versus Compatible Supplies

Each kind of supply has different trade-offs, and the right one depends on how much you print and how much hassle you will accept. New cartridges from the maker are the simplest option because the printer is designed to recognize them. They usually cost more per page, though.

Compatible cartridges come from other companies and are designed to work in the same printer. Quality and chip behavior vary between suppliers, and some printers refuse them after a firmware update. Refilled cartridges are original cartridges filled again with ink, either by a service or by you. They can save money, but the chip may still show the old level, and results depend on the ink and on how carefully the refill was done.

  • New from the maker: easiest, usually the highest cost per page.
  • Compatible: often lower cost, with variation in quality and recognition.
  • Refilled by you: lowest cost, more mess, and the chip may not reset.
  • Ink tank refill bottles: designed for refilling, with less risk of chip problems.

Before you choose, check your warranty and the maker’s policy on non-original supplies, and read the return policy of the seller. If you only print occasionally, remember that ink can dry out in cartridges that sit unused, which reduces any savings.

Refilling Safely and Cleanly

If you do refill, a careful routine reduces the chance of problems. Work on a flat surface covered with paper towels, and wear gloves if you do not want stained hands. Use the correct ink for each color and never mix colors in one chamber. Read the instructions for your cartridge or tank, because the number and position of fill points differ.

Do not overfill. Cartridges and tanks have a maximum level, and extra ink can leak into the printer or onto the head. Fill slowly and stop at the marked line if the container has one. If you can see air bubbles, let them settle before reinstalling. After filling, wipe the cartridge or the tank cap area, seal any fill holes as instructed, and handle the parts gently so ink does not drip.

Once the supply is back in the printer, expect to run a cleaning cycle to draw ink to the head. Print a nozzle check and look for gaps. If ink spilled, wipe it with a lint-free cloth and avoid getting liquid on the electronics. Keep bottles upright and tightly closed, away from children and pets, and follow the ink maker’s safety notes. Store spare ink somewhere cool and out of direct sunlight, as the post suggests, to protect quality.

Firmware Updates and Cartridge Recognition

Printer firmware is the software built into the machine, and updates can change how it treats supplies. Some updates fix bugs or add features. In some cases, updates change which cartridges the printer accepts, and you may find that supplies that worked before are rejected. The behavior depends on the maker and model, so check the policy that came with your printer.

Before accepting an update, read what it says. Many printers can be set to update automatically or to ask first, and the settings are in the menu or the maker’s app. If you rely on third-party or refilled supplies, you may prefer to turn off automatic updates, but this also means you miss security and bug fixes, so weigh the trade-off yourself.

If the printer displays a message about an unrecognized or non-original cartridge, take note of the exact wording. It can help you search the maker’s support pages and see whether the message can be dismissed or whether the printer blocks the supply entirely. Warranties and maker programs, such as subscription ink plans, may have terms about cartridge use. Read them before you refill or switch supplies, because some plans require original cartridges.

Troubleshooting Order and What to Record

When the message will not go away, work through the steps in a sensible order so you do not waste ink or time. Start with the simplest and lowest-risk checks, and move on only when the previous one has failed.

  • Confirm the correct cartridge or tank is the one flagged, and that it is fully seated.
  • Power the printer off, wait a short time and turn it on again.
  • Clean the contacts as the manual describes and reinstall.
  • Try the continue or override option, if your printer offers one.
  • Run a cleaning cycle and a nozzle check.
  • Check the maker’s support page for your model and any firmware notes.
  • Try a new cartridge to see whether the chip is the cause.

Keep notes as you go. Write down the exact message, which color is flagged, what you changed and what happened. If you contact support, these notes save time and help them identify the cause. If a new cartridge fixes it, the old one probably has a chip or ink problem. If the new cartridge shows the same message, the cause may be the printer, its sensors or the contacts inside, and the maker’s support team can advise on repair or replacement.

When the Printer Itself Is the Problem

If every supply you try is flagged, the fault may lie inside the printer. Dirty or worn contacts in the carriage, a sensor problem or a failing printhead can all trigger messages that look like ink problems. A printer that has been moved, dropped or stored for a long time may also need attention.

Look for related signs. Ink that will not flow even after cleaning, a carriage that jams, strange noises or error codes can point to hardware faults. Look up the code in the manual or on the maker’s support site. If the printer is under warranty, contact support before opening anything.

When repair costs approach the price of a new model, replacement may be the better option. If you often refill, think about what you want next. An ink tank design is built for refilling and avoids many chip problems, while a laser printer suits people who print occasionally and want low maintenance. Compare the running cost, the supply policy and the warranty, and check that your chosen model’s supplies are easy to find where you live.


Ready to Buy? Start Here — printer says out of ink after a new cartridge: what to do

Ready to Buy? Start Here

If this guide helped you decide what to look for, these products are a place to start.

Canon PG-245 Black Ink Cartridge CL-244 Color Ink Cartridge
Canon PG-245 Black Ink Cartridge CL-244 Color Ink Cartridge

View Canon PG-245 Black on Amazon

As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.

A Quick Pre-Refill Checklist

Most refill problems begin before any ink goes in. Running through a few simple checks can prevent the printer from misreading the cartridge.

  • Look up your printer model in the maker’s support pages and note which cartridge or tank type it uses.
  • Print a nozzle check or status page so you have a record of how it behaved before.
  • Work over paper towels or a tray to catch drips.
  • Wear gloves, because ink stains skin and clothes.
  • Fill only to the level the cartridge or tank allows, never to the brim.
  • Wipe the contacts and nozzle area gently with a lint-free cloth afterward.

Cartridge Style Versus Tank Style: What Changes

Printers handle ink in two broad ways, and the troubleshooting differs for each.

Type How ink is tracked Typical refill concern
Chipped cartridge A chip counts pages or reads a level The chip may still say empty after you refill
Ink tank system Level sensor or manual setting The level display may need a reset after filling
Subscription or smart cartridge Software monitors usage and supply The printer may reject non-original supplies

Knowing which type you own tells you which fix to try first. If you are unsure, the maker’s website lists the supply type for your model.

Reading the Printer Messages Closely

Printers use several similar warnings that mean different things. “Low ink” is a heads-up, “empty” may be a hard stop, and “cartridge not recognized” points to the chip or contacts rather than the ink level.

Write down what you see

Note the exact wording, any error code and the color involved. Searching the maker’s support page with that text is faster than guessing.

Learn what a warning does not tell you

A software warning is an estimate, not a measurement. Many printers count dots or pages rather than sensing real ink, which is why a freshly filled cartridge can still look empty.

Check the basics before the advanced steps

Turn the printer off and on, reseat the cartridge, and confirm the printer software is up to date. Many warnings clear with nothing more than a fresh seating.

A Calm Troubleshooting Order You Can Follow

When a warning appears, resist the urge to try everything at once. Changing one thing at a time tells you what actually worked.

  1. Power the printer off, wait a minute and switch it back on.
  2. Remove the cartridge, check it for leaks and refit it firmly until it clicks.
  3. Clean the contacts gently with a dry, lint-free cloth.
  4. Run the printer’s own cleaning or alignment routine from its menu.
  5. Look in the settings for an option to ignore the warning or reset the ink level, if the maker provides one.
  6. Install any available software or firmware update from the maker’s official site.

Keep notes on each step. If you eventually contact support, a clear list saves time and lets the agent skip steps you have already completed.

When to Stop and Ask the Maker

If you have tried reseating, cleaning and resetting without any change, it may be time to read the warranty terms and contact support. Refilling can affect what the maker covers, so check your paperwork before you try anything unusual. A leaking cartridge, a damaged chip or a printer that smells of burning should be left alone and unplugged.

For printers used for work, think about whether a new, supported cartridge makes sense for the sake of reliability. A refill is a good option for casual use, but the printer’s own supplies remain the most predictable choice.

How Your Printer Decides a Cartridge Is Empty

To fix a false empty warning, it helps to know what the printer actually measures, because it rarely measures ink the way you imagine. Most cartridges carry a small chip that reports identity and an estimated remaining level. The printer estimates consumption as it prints, counting droplets or pages against the cartridge’s expected capacity, and it reads the chip to know which cartridge it is talking to. The ink or toner itself is seldom weighed or gauged directly.

That design explains every version of this fault. A refilled cartridge still carries a chip that remembers being emptied, so the printer believes the chip rather than your eyes. A new cartridge with a damaged, dirty or incompatible chip cannot introduce itself, so the printer falls back on suspicion. A cartridge seated a fraction out of place may fail to make electrical contact at all, which the printer reports as missing, incompatible or empty depending on its mood and its firmware.

It also explains why the warning sometimes appears mid-cartridge with plenty left: the estimate is a model, not a measurement, and heavy coverage pages spend the estimate faster than the reservoir. Treat the printer’s level displays as forecasts. Forecasts can be wrong in both directions, which is why the tests below rely on what the printer prints, not only on what it says.

First Checks: Seating, Contacts and Protective Materials

Begin with the physical basics, because they cause a large share of these warnings and cost nothing to check. Power the printer on, open the cartridge access and remove the cartridge that is being rejected. Look for anything that should have been removed during installation: tape over contacts or vents, a protective clip, or a seal left in place. Packaging on chips and contacts is a classic cause of a new cartridge being treated as absent.

Inspect the chip and the printer’s matching contacts. They should be clean, bright and undamaged. If they are dusty or have ink on them, wipe the cartridge’s chip gently with a dry, lint-free cloth. Do not use liquids on electrical contacts, and do not touch them more than necessary; skin oils are part of the problem you are cleaning.

Reseat the cartridge firmly and evenly until it clicks or settles as the manual describes, then close the access door and watch the printer’s response. Many printers run a recognition routine when the door closes; give it time to finish rather than opening and closing repeatedly. If the warning clears, print a test page and a nozzle check or status page to confirm the printer is not only satisfied but actually printing with the cartridge it doubted.

Refilled and Remanufactured Cartridges: Why the Chip Disagrees

A refilled cartridge is a vessel that has been given more ink and a memory that says otherwise. Unless the chip was reset or replaced during refilling, the printer will continue to report the level it recorded when the cartridge first ran dry. Many printers will still print in this state once you acknowledge the warning, because the estimate does not physically prevent printing; the machine warns, and the human decides.

Look for your model’s acknowledgement route: an OK or resume press on the panel, a prompt in the maker’s software, or a setting that disables level monitoring for that cartridge. Maker support pages document the option where it exists. Understand the trade you are accepting: with monitoring disabled, the printer cannot warn you when the cartridge genuinely empties, so the first sign of real emptiness will be fading pages. Keep a spare ready if you run a cartridge blind.

Remanufactured cartridges with fresh chips usually report levels normally, but chip quality varies, and a cartridge that is not recognized at all, rather than recognized as empty, points at the chip or the cartridge’s fit rather than at ink. If a supplier’s cartridges repeatedly fail recognition while the printer’s original cartridge works, the evidence is about the cartridges, not the printer, and it belongs in a conversation with the supplier.

When a Genuinely New Cartridge Is Rejected

A brand-new cartridge from the printer’s maker can still be rejected, and the causes are specific. Check the cartridge is the correct one for your exact model, not merely the same family: cartridge numbers that differ by a letter often fit physically while carrying different chips or capacities, and regional variants exist as well. The printer’s manual and the cartridge box both list compatibility; compare them character by character.

Check the cartridge’s date and storage history. Cartridges that have sat for years, or in heat, can fail in ways that look electronic. Check also that the printer’s firmware is current, following the maker’s instructions; recognition tables are updated through firmware, and a printer running old firmware may not know a newer cartridge revision.

If you still have the old cartridge, swap it back as a diagnostic. A printer that accepts the old cartridge and rejects only the new one has narrowed the fault to the new cartridge itself. A printer that now rejects both has a printer-side problem, dirty or damaged contacts in the carriage, or a deeper fault, and that distinction decides whether you return a cartridge or book a repair.

The Firmware Factor, Stated Plainly

Printer firmware updates occasionally change how cartridges are recognized, and the printing world has argued about the effects for years. The practical guidance is simpler than the argument. If your printer works with the cartridges you use, there is no urgency to update firmware the moment it appears; read the maker’s release notes first. If a recognition problem appears immediately after a firmware update, that timing is evidence: check the maker’s support pages for acknowledgements and for any newer revision that addresses it.

Some printers offer settings to disable automatic firmware updates or cartridge protection features that tie cartridges to a specific machine. Where those settings exist, they are in the printer’s own menus or its web interface, documented by the maker. Changing them is a legitimate owner decision; just make it deliberately, knowing that security and bug fixes also arrive through the same update channel.

What you should not do is install firmware from anywhere other than the maker’s official support pages for your exact model. Firmware for a sibling model can disable a printer outright, and no cartridge warning is worth that trade.

Printing While the Warning Persists

Sometimes the pragmatic answer is to print anyway. If the pages come out complete and correct, the warning is an estimation error you can manage: acknowledge it, keep an eye on quality and let fading, not the display, tell you when the cartridge is truly done. Judge by output. A printer that produces perfect pages is not empty in any sense that matters.

Know the risk on inkjets specifically: running a cartridge genuinely dry can pull air into the printhead and, on some designs, damage it. The safe pattern is to treat the first visible fading as the real empty signal and change the cartridge then, rather than nursing it through many more pages. On laser printers the risk is lower; a toner cartridge run to true empty mostly just stops producing acceptable pages.

Keep records if you refill or use remanufactured cartridges regularly: which cartridge, from where, and how the printer responded. Patterns emerge quickly, and a supplier whose cartridges consistently read correctly is worth returning to, while a printer that rejects everything, including its maker’s cartridges, is telling you the fault is its own.

More Questions About False Empty Warnings

Why does the warning appear right after I install a full cartridge?

Because recognition and estimation happen at installation, and that is when a chip problem, a seating problem or a leftover protective seal announces itself. Work through the physical checks first, then the compatibility check, then swap the old cartridge back as a diagnostic. The timing is a clue: installation-time warnings are almost never about ink quantity.

Can cleaning the chip contacts damage the cartridge?

Done gently with a dry, lint-free cloth, it is the standard remedy and is recommended in many makers’ own guides. The damage risks are liquids, abrasives and force. Keep all three away from the contacts and you are performing maintenance, not surgery.

The printer will not print at all while it shows the warning. Is that normal?

Some models block printing on an unrecognized cartridge while allowing it on a recognized-but-estimated-empty one, and the distinction matters. An unrecognized cartridge is an identity problem, chip, fit or compatibility. A recognized cartridge with a low estimate usually offers an acknowledgement path. Read the exact wording of the message on the panel; makers phrase the two states differently, and the wording tells you which problem you have.

Will resetting the printer clear a false empty warning?

A restart sometimes clears a confused state, and it is worth one attempt. A factory reset is a heavier tool that also erases your network and preference settings, and it does not rewrite what a cartridge’s chip reports, so it rarely cures chip-based warnings. Save resets for after the physical and compatibility checks, not before.

Tank Printers and Toner Bottles: The Same Warning, Different Hardware

Refillable tank printers sidestep cartridge chips but have their own version of this fault. The printer estimates tank levels from usage, and after a manual refill it may keep reporting the old estimate until you tell it the tank was filled, using the level-reset procedure in its menus or software. An owner who refills without resetting sees a confident empty warning above a visibly full tank, and the cure is the reset step, not another bottle of ink.

Tank systems also ask you to confirm which tank was filled, and confirming the wrong one leaves the warning exactly where it was while corrupting the estimate for the tank you named. Refill slowly, confirm carefully, and check the levels display after the reset to see all four tanks reporting what your eyes report.

Laser printers with separate toner and drum units add one more identity to check: some warnings that mention a cartridge are actually about the drum unit’s counter reaching its programmed life. The message wording names the unit; read it literally before ordering toner for a drum problem or a drum for a toner problem.

A Short Diagnostic Sequence to Keep

When the warning appears, this order resolves most cases fastest. One: read the exact message and note whether it says empty, low, unrecognized or incompatible. Two: reseat the cartridge and check for seals, tape and clean contacts. Three: confirm the cartridge number matches your model exactly. Four: swap the old or a spare cartridge in to learn whether the fault follows the cartridge or stays with the printer. Five: check the maker’s support pages for your model and the message’s exact wording, and consider firmware only after the first four steps.

Notice what is not in the sequence: buying another cartridge immediately. A second cartridge is a diagnostic only when it is known-good, ideally the maker’s own. Buying an identical twin of a cartridge that may be incompatible just doubles the evidence against the wrong suspect.

My printer accepts the cartridge but the level never moves from empty. Should I worry?

If pages print correctly, treat it as a monitoring fault rather than a printing fault: the printer has lost track of quantity but not of function. The real empty signal becomes fading output, so keep a spare on hand. If the machine is under warranty, report the behavior, because level sensing that never recovers after the standard checks is a legitimate defect to have documented while coverage lasts.

Finally, a note on honesty in both directions. A printer crying empty over a full cartridge is annoying, but the opposite failure, a printer contentedly reporting plenty while the cartridge fades, is the one that ruins deadline print runs. Whichever way your machine errs, the habit that protects you is the same: judge by printed pages, keep a spare within reach, and let the display advise rather than command.

Subscription Ink Services and Cartridge Warnings

Printers enrolled in ink or toner subscription services add a layer to this problem. Service cartridges are tracked by the program, and their warnings may relate to the subscription’s accounting, a missed connection that prevented usage reporting, or a cartridge that belongs to the program rather than to retail stock. If your printer is enrolled, check the service’s own app or account pages before treating a warning as a hardware fault, because the remedy may be account-side: reconnecting the printer so it can report, or requesting a replacement through the program.

Mixing service and retail cartridges confuses some machines’ accounting, and ending a subscription can change how its cartridges behave afterward. If a warning began exactly when a subscription started, lapsed or was cancelled, that timing is the headline clue, and the service’s support channel is the fastest route, since they can see the account state that no panel menu shows you.

Why does the warning return after every restart even though I acknowledged it?

Acknowledgement is usually per-session: the printer notes your decision while it stays powered, then asks again after a restart because the underlying estimate has not changed. That is expected behavior for a chip that still reports empty. The warning truly ends only when the estimate changes, through a recognized cartridge, a level reset where the design supports one, or a monitoring setting that disables the prompts. If the printer also loses other settings at every restart, that broader amnesia is worth reporting as its own fault.

Keep the old cartridge until the new one has printed successfully for a few days, whatever the warning says. It is your best diagnostic tool, your emergency fallback and, if the new cartridge proves faulty, your evidence in the returns conversation. Storage is simple: back in its packaging or a sealed bag, out of heat and bright light, where it will stay usable for exactly these purposes.

And if the printer rejects every cartridge you own, including the one it printed with happily last week, stop buying cartridges. At that point the evidence has converged on the printer: its contacts, its carriage or its recognition system. Clean the printer-side contacts once, gently, with the machine unplugged, and if that changes nothing, the next step is the maker’s support line or a service visit, with your notes about which cartridges were tried and what each attempt reported.

Bring those notes to the conversation. Support teams resolve cartridge-recognition cases far faster when the owner can already say which cartridges were tried, in which order, and what the panel reported each time, because that sequence is precisely the evidence their own diagnostic script would have asked you to gather.

Most owners, though, will never need that call: a reseat, a cleaned contact or a correctly matched cartridge ends the great majority of these warnings.

Start there, in that order, every time.

The physical checks come first because they are fast, free and, far more often than the software theories, correct.

Frequently Asked Questions

Can I refill cartridges?

You can, but the printer may not recognize them, and quality can vary. Check your warranty.

Why does an ink tank printer say empty after I refilled?

The tank may need to be filled above the minimum, and the printhead may need priming with a cleaning cycle.

Can I reset the ink level?

Some printers allow it. Check your manual.

Is it safe to ignore the low-ink warning?

Yes for a short time, but print quality may suffer.

Why does the printer say empty when I can see ink inside?

The printer reads a chip or a counter, not the actual ink you can see. The stored value can say empty even when the container is full. Reseating the cartridge, using an override option or replacing the cartridge may help.

Will a firmware update stop my refilled cartridges working?

It can on some models, because certain updates change which supplies the printer accepts. Check the maker's policy and the update notes. You can often set the printer to ask before updating.

Can a refill void my warranty?

It depends on the maker and the terms of your warranty or plan. Read the warranty document or the support pages before refilling. If you are unsure, ask the maker's support team.

How do I know if the chip is the problem?

Try a new cartridge of the same type. If the message disappears, the old chip was the likely cause. If it stays, the contacts or the printer may be the problem.

Should I refill when the printer first warns about low ink?

There is no need to rush, because the warning is an estimate and the printer can often keep printing. Many people wait until print quality fades. Check your manual for how your model behaves.

What should I do if ink leaks during a refill?

Stop, switch the printer off and wipe the spill with a lint-free cloth or paper towel. Keep liquid away from electronics and let parts dry before using them. Check the manual for cleaning advice.

Can mixing ink brands cause problems?

Inks from different makers may differ in how they behave, and mixing them in one chamber is not advised. Use ink designed for your printer and fill each color separately. Check the manual for guidance.

How can I make refills last longer?

Print a short page regularly to keep the nozzles active, store spare ink cool and sealed, and avoid overfilling. Reduce draft printing if it wastes ink. Check the nozzle pattern now and then.

Bottom Line

The printer usually reads a chip or counts pages, so it does not know you refilled. Reseat and clean the contacts, override the warning where allowed and prime the head. See how to stop printer ink drying out to avoid clogs.

More Printer Guides