Disclosure: As an Amazon Associate, reviewstook.com earns from qualifying purchases. Links to Amazon on this page are affiliate links; they cost you nothing extra.
Connecting speakers to a turntable depends on what the turntable has built in. Some turntables have a built-in preamp, some need an external phono preamp, and some speakers have a phono input. Getting the combination wrong gives you very quiet or distorted sound. This guide walks through the options and the steps.
This guide is based on general audio knowledge and product information, not our own testing.
By the Reviewstook Editorial Team. Last updated: October 31, 2026.

Understand the Preamp
A turntable outputs a very weak signal that needs a phono preamp to boost it and apply the correct equalization. Without a preamp, the sound is thin and quiet. Some turntables include a preamp, usually with a switch labeled “Phono/Line”. Others need an external preamp, or a receiver or speaker with a phono input.
In this guide
Option 1: Turntable With Built-In Preamp and Powered Speakers
Set the turntable’s output switch to Line, then connect its RCA cables to the line input of powered speakers or an amplifier. This is the simplest setup. See our bookshelf speakers and speakers for turntables.
Option 2: Turntable Without Preamp
Connect the turntable to a phono preamp, then connect the preamp to powered speakers or an amplifier. Or use a receiver with a phono input. Connect the ground wire to the grounding post to avoid hum.
Option 3: Record Player With Built-In Speakers
Some record players have built-in speakers and need no extra connections. Their sound is basic. See our record players with speakers.
Option 4: Bluetooth
Some turntables have Bluetooth output. This lets you play to Bluetooth speakers, with some delay and compression. It is convenient for casual listening.
Step-by-Step Setup
- Place the turntable on a stable surface away from the speakers.
- Check the preamp: set Phono/Line accordingly.
- Connect RCA cables (red to red, white to white).
- Attach the ground wire if there is one.
- Connect to powered speakers or an amplifier with passive speakers.
- Set the volume low, play a record and adjust.
Troubleshooting
If the sound is very quiet, add or enable a preamp. If you hear hum, check the ground wire and move the turntable away from power cables. If one channel is missing, check the RCA cables. See our guide to powered vs passive speakers.
Cartridge Types and Why They Affect the Setup
The cartridge sits at the end of the tonearm and holds the stylus that reads the groove. Most turntables use one of two types, and the difference affects which preamp you need. Moving magnet cartridges produce a stronger signal and are the common type on entry-level and mid-range turntables. Moving coil cartridges produce a much weaker signal and need a preamp designed to handle them, often with adjustable gain or a step-up stage.
When you buy a preamp or a receiver with a phono input, check which cartridge types it supports. Many inputs are made for moving magnet cartridges only. If your turntable has a moving coil cartridge, look for an input or preamp that explicitly lists support for it. The product listing or manual should say.
- Check the cartridge: look at the turntable specifications for the type, or read the cartridge label.
- Look at the gain setting: some preamps have switches for different cartridges.
- Do not guess: an incorrect match can give very quiet or distorted sound.
- Stylus care: a worn stylus sounds dull or distorted, and may damage records. Replace it when the maker advises.
If you are unsure, take a photo of the turntable and cartridge, and ask the seller or maker which preamp type fits. This is a better step than buying and returning equipment.
Active and Passive Speakers With a Turntable
The kind of speaker you have decides the chain of equipment between the turntable and the sound. Active speakers, also called powered speakers, have an amplifier built in, so you connect the signal from the turntable or preamp directly to them. Passive speakers have no amplifier and need a separate amplifier or receiver to drive them.
Many powered speakers list a line input with RCA connectors, which suits a turntable that has a built-in preamp set to line, or a separate preamp. Some powered speakers have a phono input of their own, which means you can connect a turntable directly without an extra preamp. Check the back panel and the manual for this label, since an unlabeled input is a line input.
- Powered speakers with line input: use a preamp or a turntable with built-in preamp.
- Powered speakers with phono input: connect the turntable directly, with the ground wire.
- Passive speakers: need an amplifier or receiver with speaker terminals and, if it lacks a phono input, a preamp.
- Speaker wire: choose wire suited to the length, and make sure bare ends do not touch each other at the terminals.
Whichever route you choose, turn the volume down when you connect or switch things on. A sudden signal can be loud and may damage equipment.
Placing the Turntable and Speakers to Reduce Feedback
Records are sensitive to vibration, and speakers produce a lot of it. If the turntable sits on the same surface as a speaker, sound energy can travel into the stylus, causing a low rumble or a loud feedback loop. Place them thoughtfully to prevent this.
Put the turntable on a stable, level surface that does not shake when you walk across the room. A solid shelf, a heavy cabinet or a wall-mounted platform works better than a wobbly table. Keep the speakers on separate stands or furniture, with some distance between them and the turntable. Level the turntable with a small spirit level, and make sure the dust cover can open without touching the wall.
- Avoid shared surfaces: do not put speakers on the same shelf as the turntable if possible.
- Use isolation feet or a mat: they can reduce vibration, though their effect varies.
- Keep cables apart: signal cables should not run alongside power cables, which can cause hum.
- Mind the room: speakers near corners or walls may sound boomy, so experiment with distance from walls.
- Check the dust cover: it should be closed during playback if the maker advises, as it helps cut down vibration and dust.
If you hear a low thumping when you turn up the volume, lower the level and increase the distance between the turntable and the speakers before assuming the equipment is faulty.
Setting Up the Tonearm and Tracking Force
A turntable needs a correct physical setup for the sound to be right, whatever speakers you use. The most important adjustments are tracking force and anti-skate, which control how the stylus sits in the groove. Tracking force is the downward pressure on the stylus, and the cartridge maker specifies a range. Too light and the stylus can skip or mistrack. Too heavy and it can wear records and stylus faster.
Many turntables have an adjustable counterweight on the tonearm. Follow the manual to balance the arm, set the weight, and then apply the anti-skate setting. Some entry-level turntables come pre-adjusted, so check before changing anything.
- Use a stylus force gauge: they are inexpensive and give a more reliable reading than guessing.
- Keep the platter level: an unlevel platter changes arm behavior.
- Check the belt or drive: a loose or worn belt can cause speed drift and sound that wavers.
- Select the correct speed: make sure the speed matches the record.
- Clean records: a carbon fiber brush before each play helps keep the stylus clean.
- Handle the tonearm carefully: use the cue lever when lowering it.
If the cartridge is delicate or you are unsure, ask a shop or follow the maker’s instructions. A careful setup improves sound and protects your collection.
Upgrading a Record Playback System Step by Step
Many people start with a simple system and improve it over time. A sensible order avoids wasted money and lets you hear what each change does. Start with the basics: a stable, level surface and a properly set up turntable. Then work through the signal chain, asking what limits the sound.
- Records and cleaning: clean, undamaged records make a bigger difference than many hardware changes.
- Stylus: a fresh or better stylus can improve clarity and reduce wear.
- Preamp: a separate preamp can be an improvement over a basic built-in one, if your turntable allows bypassing the internal stage.
- Cables: good quality, properly shielded RCA cables are enough. Expensive exotic cables are not necessary.
- Speakers: they often have the largest effect on the overall sound, so choose a pair that fits your room and listening habits.
- Amplifier or receiver: match its power and connections to your speakers.
- Room treatment: rugs, curtains and bookshelves can tame echoes.
Budget tiers differ mainly in build, adjustability and sound refinement. A modest system that is set up well will often sound better than an expensive one that is not. Before buying, check that each new component has the inputs, outputs and cartridge support that you need, and ask about a return window so you can test it at home.
Which cables and connectors do you need to connect speakers to a turntable?
Most setups need one pair of RCA cables, and sometimes a grounding wire or a speaker wire. Which of these you need depends on where the signal goes next: powered speakers, a preamp, or an amplifier.
RCA cables carry the left and right channels, and they are color coded, with red for the right channel and white for the left. Many turntables have the cable permanently attached, while others have sockets so you can swap the cable. If your turntable has a fixed cable, you only need to buy a cable for the next link in the chain, such as preamp to speakers.
- RCA to RCA: the usual link from turntable to preamp, or from preamp to powered speakers.
- RCA to 3.5 mm: sometimes needed when powered computer speakers use a headphone-style input. Check the speaker manual first.
- Ground wire: a thin wire from the turntable to a grounding post on the preamp, receiver or amplifier. It prevents hum.
- Speaker wire: only for passive speakers connected to an amplifier or receiver.
- Power cables: every powered component needs a socket, so count your outlets before you start.
Choose cable lengths that let the turntable sit away from the speakers without stretching the cable tight. A cable that is too short forces you to place the turntable near the speakers, which brings back the vibration problem.
Which turntable speaker setup should you choose?
Choose the simplest chain that covers your turntable’s output and your speakers’ inputs. The right option depends on your turntable, your space and how much equipment you want to own.
This guide does not name specific products, so use the four options above as your decision guide and match them to your situation.
- If your turntable has a built-in preamp and you want the easiest setup: go for Option 1, with the switch on Line and a pair of powered speakers.
- If your turntable has no preamp and you already own an amplifier or receiver: check for a phono input on it. If it has one, plug in directly. If not, add a separate phono preamp.
- If you want one box and have little space: a record player with built-in speakers needs no extra connections, though sound quality is basic.
- If you want to listen across the room without cables: a turntable with Bluetooth output suits casual listening, but expect some delay and compression.
- If you care about sound and plan to upgrade over time: choose a turntable with a replaceable cartridge and a way to bypass its internal preamp, then add components in the order described earlier.
If two options seem equal, pick the one with fewer boxes and cables. Every extra component is another place for hum, loose connections or incompatibility.
What should you check before you buy speakers or a preamp for your turntable?
Check the inputs and outputs on every piece of equipment before you buy, because a mismatch is the most common reason a new purchase does not work. The product listing and the manual should answer each of these questions.
- Phono or line input: does the speaker or receiver say Phono, or only Line or Aux? An unlabeled input is a line input.
- Cartridge support: does the preamp list support for your cartridge type, moving magnet or moving coil?
- Built-in preamp: does your turntable have one, and is there a switch to turn it off if you add your own?
- Ground connection: is there a grounding post for your turntable’s ground wire?
- Power: does the preamp need its own power supply, and is it included?
- Cables included: are RCA cables in the box, and are they long enough?
- Speaker type: powered speakers need only a socket, while passive speakers need an amplifier with speaker terminals.
- Space: will the speakers and turntable fit on separate surfaces with room to breathe?
- Returns and warranty: confirm the return window and warranty terms on the listing, so you can test the setup at home.
Write these answers down for your own equipment first. Then compare them with each listing before you press the buy button.
How do you fix hum, distortion or a missing channel after connecting your turntable?
Work through the chain one link at a time, starting with the simplest causes. Most problems come from a switch in the wrong position, a loose plug or a missing ground wire.
Hum or buzz. Make sure the ground wire is attached at both ends. Move signal cables away from power cables and power adapters. Try a different outlet, since some outlets share circuits with equipment that causes interference.
Distorted or harsh sound. A preamp stage may be doing the job twice. If your turntable has a built-in preamp and you also use a phono input, the signal is boosted twice. Set the turntable to Line when using an external amplifier input labeled Line, and use Phono mode only when the next input expects a raw signal. A worn stylus can also cause distortion.
Very quiet or thin sound. The signal is probably not getting a preamp stage. Check the Phono/Line switch and the input you chose on the receiver.
One channel missing. Reseat the RCA plugs and swap the cables to see whether the fault follows the cable or the equipment. Also check the balance control on the amplifier.
Sound too fast or slow. Check the speed selector and the belt. A stretched belt can make pitch drift.
Change one thing at a time. If you change several at once, you will not know which fix worked.
Is a separate phono preamp worth it, and who should skip it?
A separate phono preamp is worth it when your turntable has no built-in stage, when your receiver has no phono input, or when you want more control over sound. It is not necessary for everyone.
The honest trade-offs are simple. An external preamp adds another box, another cable and another power connection. In return, it may offer better handling of your cartridge, adjustable settings and an upgrade path. Whether you will hear the difference depends on your speakers, your room and your records.
- Who should consider one: owners of a turntable without a preamp, people with a moving coil cartridge, and anyone upgrading step by step.
- Who can skip it: owners of a turntable with a built-in preamp who are happy with the sound, and anyone using speakers or a receiver that already has a phono input.
- Is paying more worth it? Higher budget tiers usually bring better build and more adjustment. A modest preamp matched to your cartridge is often a better first step than an expensive one that does not suit it.
Before you decide, list what your turntable, speakers and receiver already provide. Compare that with the checklist above, check the current listing for inputs and what is included, then choose the setup that fits how you will use it.


Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
The Signal Chain, Stage by Stage, So Faults Have Nowhere to Hide
Every turntable setup, however simple it looks, is a chain of the same stages: cartridge, phono equalisation and gain, line-level signal, amplification, speakers. When sound is missing, quiet, distorted or humming, the fault lives in exactly one of those stages or in a connection between two of them. Learning to point at the stage is worth more than any single tip in this guide, because it turns troubleshooting from guesswork into a short sequence of tests.
The cartridge produces the smallest signal in the whole system, far weaker than anything a phone or streamer makes. That is why its cables are short, why the ground wire exists, and why a turntable must never be plugged straight into an ordinary input and judged: without the phono stage’s gain and equalisation the music is a whisper with no bass and piercing treble, exactly as the earlier sections of this guide describe. The phono stage, whether built into the turntable, the amplifier or a separate box, is not an accessory. It is half the instrument.
After the phono stage, everything behaves like any other audio source, and that is the liberating fact of turntable setup. From that point you can use powered speakers, a receiver, a soundbar or a computer input with the same confidence as any other device, provided levels are sensible. If you ever upgrade one part of the chain, upgrade with the chain in mind: a better cartridge deserves a phono stage that can do it justice, and better speakers will faithfully reveal a humming cable you previously never noticed.
Grounding in Depth: The Wire People Ignore Until It Sings
The ground wire earns a section of its own because it causes a disproportionate share of turntable misery. Its job is to give electrical noise a harmless path away from the delicate cartridge circuit. When it is missing, loose or attached to a painted or corroded point, the system advertises the fact with a hum that rises with the volume control. Attach it to the designated grounding post, tightened onto clean metal, and route it alongside the signal cables rather than across the room on its own adventure.
Not every combination hums without it, which is why some owners disconnect it and get away with it, but that is luck about their particular equipment and wiring, not a method. If your turntable has the wire, connect it. If hum persists with it connected, the systematic approach is to change one thing at a time: reseat the signal plugs, move the power supplies of nearby devices, try a different mains socket for the turntable, and check whether the hum changes when you touch the tonearm, which tells you the grounding path is involved. Hum that appears only when a particular lamp, charger or computer wakes up is being imported from that device, and distance plus tidy cable routing usually cures it.
One warning belongs here: never solve hum by defeating the safety earth of any mains-powered equipment. The ground wire discussed in this guide is a signal reference, not a safety device, and the two must never be confused. If a setup hums stubbornly despite methodical checks, that is a job for the equipment maker’s support, not for improvisation with mains wiring.
First Play: A Calm Checklist for the First Record
With everything connected and volumes low, choose a record you know well and that is in decent condition; a battered charity-shop find makes a poor test disc because you cannot tell its faults from the system’s. Lower the stylus into a quiet passage near the start. You should hear the music arrive evenly in both channels with the bass restored by the phono equalisation. Listen first for balance, then for noise: a gentle surface texture is normal, a loud hum, a buzzing that follows your hand near the cables, or music in one channel only are faults to fix now, at low volume, before your first full side.
Work through the listening checks in order. Centre a vocal and confirm it sits between the speakers. Play a bass-heavy passage and walk the volume up gradually, watching for the woofer pumping or feedback howl that means the turntable is hearing its own speakers. Check the quietest passage you know for hum. Only when all three checks pass should you settle in. That five-minute ritual, done once, is the difference between a system you trust and one you keep half-suspecting.
Write down what worked: which input, which switch positions, where the ground wire went, and the volume settings that suit a record. Turntable setups have more switches in more places than any other source, and the note saves you re-deriving the whole chain the first time a helpful hand tidies the cables or a switch gets knocked during dusting.
Keeping the System Quiet: Habits After the Setup Works
A turntable system that is silent and musical on day one can drift into small faults over months, and nearly all of them are maintenance rather than failure. Dust builds on the stylus and announces itself as a fuzzy, distorted top end that owners often blame on their records; a proper stylus brush or cleaner, used as its maker directs, restores the sound in seconds. Connections oxidise slowly, especially in humid rooms, and an intermittent crackle when a cable is touched is cured by unplugging, inspecting and firmly reseating each plug in turn. Belt-driven turntables eventually stretch their belts, which shows up as music that sounds subtly seasick in pitch on sustained notes, and a fresh belt is an inexpensive cure.
Keep a short routine. Every few months, play a familiar record and listen deliberately for hum, channel balance and pitch steadiness. Check that the ground wire is still tight, that the signal cables have not been crushed by furniture or chewed by the household’s smaller residents, and that the turntable is still level, since a knocked stand changes both tracking and sound. Catching these small drifts early is the difference between a system that ages gracefully and one that accumulates mysteries until its owner stops using it.
Finally, change one thing at a time when you do upgrade. A new cartridge, a new phono stage and new speakers fitted on the same weekend leave you unable to say which change helped, which hurt, and which introduced the hum you now have. Sequential changes, each settled and understood before the next, are slower and far more satisfying, and they are how experienced vinyl listeners build systems that stay built.
Variations You Will Meet: Radios, All-in-One Decks and Suitcase Players
Not every record player arrives as a bare turntable waiting for a textbook chain. All-in-one decks with built-in speakers usually offer a line output as well, and connecting proper speakers to that output follows the same rules as any turntable with its preamp switched on: the signal leaving the deck is already at line level, so it feeds powered speakers or an amplifier’s ordinary input directly, and the improvement over the built-in speakers is often the single biggest upgrade such a deck can receive. Check whether using the output mutes the internal speakers or plays through both, because designs differ and playing through both rarely sounds better.
Suitcase-style players deserve a specific warning. Many have a line output and benefit from real speakers exactly as described, but their cartridges and styli are basic, and no speaker can recover detail the stylus never traced. Connect better speakers by all means, since the improvement is real and the cost modest, but keep expectations in proportion: the speakers reveal the deck as it is. If the upgrade leaves you wanting more, the next step is a better turntable, not better speakers again.
At the other end, some turntables offer digital outputs or built-in conversion for computer recording, and some amplifiers accept a turntable through a digital input after conversion. These routes work, and they follow the same golden rule in a new costume: the phono equalisation and gain must happen somewhere, exactly once, before the signal is treated as an ordinary source. Find where your equipment performs that step, make sure it happens once and only once, and every connection downstream becomes ordinary. Nearly every confusing turntable setup in the world reduces, in the end, to that step happening twice, not at all, or in the wrong place.
A Short Word on Keeping a Setup Diagram
Every turntable owner eventually benefits from a simple diagram of their own system: which cable runs from the turntable to which input, where the phono stage lives and how its switches are set, where the ground wire is attached, and which volume settings suit a record. Draw it on paper and keep it with the records, or photograph the back of the equipment with the connections labelled. The diagram pays for itself the first time the system is moved, cleaned around, or inherited by another member of the household, and it turns every future fault from an archaeological dig into a comparison against a known-good state. Systems documented this way stay working for decades, because their owners can always return them to the day they worked.
Frequently Asked Questions
Do I need a preamp for my turntable?
Yes, unless the turntable, receiver or speakers have one built in.
Why is my turntable so quiet?
The preamp may be missing or the switch is on the wrong setting.
Can I use Bluetooth speakers?
If the turntable has Bluetooth output, yes.
Why do I hear hum?
Usually a missing ground connection or nearby power cables.
What is the difference between moving magnet and moving coil cartridges?
Moving magnet cartridges output a stronger signal and suit most standard phono inputs. Moving coil cartridges output a weaker signal and need a preamp that supports them.
Can I plug a turntable into a normal line input?
Only if the turntable has a built-in preamp set to line output, or you use a separate preamp. Otherwise the sound will be very quiet and thin.
What are powered speakers?
They have an amplifier built in, so you can connect a turntable or preamp directly. Check the back panel for line or phono inputs.
Why does my turntable rumble when I turn the volume up?
Vibration from the speakers may be reaching the stylus through shared furniture. Increase the distance and use separate surfaces.
Do I need special cables for a turntable?
Standard shielded RCA cables are fine for most setups. Keep them away from power cables to avoid hum.
How do I set the tracking force?
Follow your cartridge maker's recommended range and use the counterweight, ideally with a stylus force gauge. Check the manual for anti-skate settings.
When should I replace the stylus?
When the sound becomes dull, distorted or noisy, or after the usage period the maker suggests. A worn stylus can damage records.
Can you connect a turntable directly to speakers?
Only if the speakers are powered and have a phono input, or if the turntable has a built-in preamp set to line output. Otherwise you need a preamp. Passive speakers always need an amplifier as well.
Which way round do RCA cables go?
Red goes to the right channel and white goes to the left channel, on both ends of the cable. If you swap them, the stereo image is reversed but nothing is damaged.
Can you connect a turntable to a TV or soundbar?
Only if the soundbar or TV has an input that suits the signal. Use a turntable set to line output or a separate preamp, and check that the input is an RCA or auxiliary type. Check the manual, since many TVs and soundbars have no analog inputs.
Do you need a receiver to use a turntable with speakers?
Not always. Powered speakers with a line input, plus a preamp or a turntable with a built-in one, can work without a receiver. Passive speakers do need an amplifier or receiver.
What does the Phono/Line switch do on a turntable?
It turns the built-in preamp on or off. Set it to Phono if the signal goes to a phono input, and to Line if it goes to a normal line input. Wrong settings cause very quiet or distorted sound.
Why is there a ground wire on my turntable?
It reduces hum by giving stray electrical noise a path to the grounding post. Connect it to the post on the preamp, amplifier or receiver. If your equipment has no post, check the manual for what the maker advises.
Can a computer speaker set work with a turntable?
It can if the speakers are powered and you add a preamp or use a turntable with built-in preamp. Check the input type, since some computer speakers use a 3.5 mm input that needs an adapter.
Can I listen through headphones as well as speakers from one turntable?
Yes. If your amplifier or receiver has a headphone socket, it usually mutes or keeps the speakers according to its design, and the turntable chain needs no changes. With powered speakers and no amplifier, you will need a phono stage or a small box that offers a headphone output, or a turntable whose built-in electronics provide one. The phono stage still has to come before the headphone listening point in the chain, exactly as it does for speakers.
Why does the sound break up on loud passages even though quiet ones are fine?
Loud passages are where a mistracking stylus, a wrongly set tracking force or an overloaded input shows itself first, because the groove swings widest there. Check the tracking force against the cartridge maker’s recommendation, confirm the stylus is clean and undamaged, and make sure you have not connected a turntable with its built-in preamp switched on into a phono input, which overloads it. Work through those three in order and you will find most cases.
Can I split the turntable signal to feed two sets of speakers?
After the phono stage, the line-level signal can be shared more easily than before it, but simple splitter cables are a compromise: they can lower the level, upset the loading the phono stage expects to see if placed before it, and invite hum. The cleaner solutions are an amplifier with two outputs, a source switch, or a second phono stage. Never split the delicate cartridge signal itself; whatever you share, share it after proper phono amplification.
Does it matter which mains sockets the turntable and speakers use?
Sometimes. Equipment powered from widely separated sockets, especially on different circuits, can occasionally develop a hum through the interconnecting cables. Powering the turntable chain from sockets in the same area, ideally the same strip used sensibly and within its rating, removes that variable. If you move the system and a new hum arrives, suspect the new power arrangement before suspecting the equipment that worked yesterday.
Bottom Line
Find out whether you have a preamp, connect with RCA cables and the ground wire, and use powered speakers or an amplifier. See our best speakers for turntables for picks.
Related Reading
- Soundbar Buying Guide: Channels, Atmos, HDMI ARC and Subwoofers
- 6 Best Soundbars for TV
- 6 Best 2.1 Computer Speakers with Subwoofer: PC and Gaming
- 4 Best 4×6 Car Speakers: Pioneer, Kicker, Pyle
- 4 Best 5.25-Inch Car Speakers: Pioneer, Kicker, BOSS
More Speaker Guides
- Best Record Players with Speakers
- Best Speakers for Turntables
- Best Powered Bookshelf Speakers
- Powered vs Passive Speakers
- All speaker guides
Related Guides
- 6 Best Portable Bluetooth Speakers: Pocket to Outdoor (2026)
- 6 Best Waterproof Bluetooth Speakers: IPX5 to IP68 Explained
- 6 Best Shower Speakers: Bluetooth, Waterproof and Suction (2026)
- 5 Best Party Bluetooth Speakers: Loud, Bassy and Portable (2026)
- 5 Best Bluetooth Speakers Under $50: Cheap and Waterproof (2026)




