Polling rate is how many times per second a mouse reports its position to the computer. It is measured in hertz, and it is one of the spec numbers that gets inflated by marketing. This guide explains what it does and whether you should change it.
This guide is based on general knowledge, not our own testing.
By the Reviewstook Editorial Team. Last updated: October 31, 2026.

What Polling Rate Means
At 125 Hz a mouse reports its position 125 times per second, or every 8 ms. At 1000 Hz it reports every 1 ms. Higher rates reduce the delay between moving your hand and the cursor responding.
In this guide
Common Rates
125 Hz is typical for office mice. 500 Hz is a mid setting. 1000 Hz is the standard for gaming mice. Some mice advertise 2000, 4000 or 8000 Hz.
Does Higher Mean Better?
Going from 125 to 1000 Hz makes a visible difference in smoothness. Beyond 1000 Hz the benefit is small for most players, and higher rates use more CPU and battery, which can cause stutter on weaker PCs.
How to Change It
Use the mouse maker’s software to set the polling rate. Test games and check the battery on wireless mice.
Polling Rate and DPI
They are different. DPI sets how far the cursor moves per inch of hand movement. Polling rate sets reporting frequency. See our DPI guide.
Recommended Settings
Use 1000 Hz for most gaming. Try higher rates only if your PC and mouse support it and you notice a difference. See Windows mouse settings.
Polling Rate, Frame Rate and Latency: How They Fit Together
Polling rate is only one link in the chain between your hand and the screen. The sensor reads movement, the mouse processor packages it, the USB or wireless link delivers it, the game reads it on its next frame and the monitor finally shows the result. A faster polling rate shortens only one of those steps.
The time between reports is simply one divided by the rate. At 125 Hz it is 8 ms, at 500 Hz it is 2 ms, at 1000 Hz it is 1 ms, at 2000 Hz it is 0.5 ms and at 8000 Hz it is 0.125 ms. A game running at 60 frames per second shows a new image only every 16.7 ms, so cutting the report interval from 1 ms to 0.125 ms barely changes what you see. At 240 frames per second the frame interval is about 4.2 ms, and the extra reports start to matter a little more, mainly by making cursor movement smoother and more consistent.
What Higher Polling Rates Cost
- CPU load: the computer has to process every report. At 8000 Hz that is eight times the interrupts of 1000 Hz, which can cause stutter in CPU-heavy games on older processors.
- Battery life: wireless mice send more data at higher rates and drain faster. Many wireless mice list battery hours at 1000 Hz or lower.
- Compatibility: some USB ports, hubs and extension cables handle high rates poorly. Plug the mouse or its receiver directly into the computer.
- Software: not every game handles high reporting rates smoothly, and some menus misbehave.
How to Check Your Current Polling Rate
Open the maker’s software and look under performance or sensitivity settings. You can also use a web-based polling rate test: move the mouse in circles over the page and read the measured rate. Results vary with how smoothly you move, so do not worry about small differences. If the measured rate is far below the setting, check the USB port, remove hubs and close background software.
When a Change Is Worth Trying
- You use a 240 Hz or faster monitor and play fast shooters.
- Your PC has a fast processor and you have headroom in frame rate.
- You notice choppy cursor movement at 125 or 500 Hz.
- You are using a wired mouse or a wireless mouse with a good battery.
If none of these apply, leave the mouse at 1000 Hz. It is the standard because it balances smoothness and system load.
Troubleshooting Polling Problems
- Cursor stutters at a high rate: drop to 1000 Hz or 500 Hz and test again.
- Wireless mouse disconnects: move the receiver closer using a short extension cable and keep it away from other radios.
- The rate resets: save a profile to the mouse or update the firmware.
- Windows power saving: disable USB selective suspend and power-saving options for the port in Device Manager and Power Options.
Polling rate and DPI are separate settings. Read our DPI guide and Windows mouse settings for gaming to tune the rest of the chain.
Wired Versus Wireless and Bluetooth Polling
Polling rate behaves differently depending on how the mouse connects. A wired mouse sends reports over a cable, so the rate you select in software is usually the rate you get, within the limits of the port and the computer. A mouse using a 2.4 GHz receiver is designed to behave much like a wired one for games, but the radio link, battery and interference can all affect how consistent the reports are. Bluetooth is a different story: it is built for convenience and low power, and many mice run at a lower or less consistent reporting rate over Bluetooth than over a receiver or cable.
That means a mouse with an impressive polling figure on its box may only reach it in one mode. Read the product page or manual to see which connection each rate applies to. If a spec sheet quotes the highest rate, ask whether it needs a particular receiver, a wired connection or a specific software setting.
Practical advice for each type:
- Wired: use a good cable and plug it directly into the computer, not a crowded hub.
- 2.4 GHz wireless: keep the receiver near the mouse pad, use a short extension if needed and avoid placing it behind the computer.
- Bluetooth: accept that it is intended for everyday tasks and laptops, not for the most demanding play.
If you are unsure, try your usual game in each mode and see whether you notice any difference in smoothness before deciding which to use.
Monitor Refresh Rate and What You Can Notice
Your monitor decides how often you see a new image, and that limits how much of a faster polling rate you can perceive. A 60 Hz display shows a new frame roughly every 16.7 ms, and a mouse reporting every 1 ms already sends many updates between frames. Increasing the rate further adds reports that the display cannot show individually. On a higher refresh monitor the gap between frames is smaller, so extra reports are a little more likely to produce a smoother-looking cursor.
It helps to match each part of your setup to your goals:
- On a standard-refresh monitor, 1000 Hz is more than adequate for nearly every use.
- On a fast monitor with a game that holds a high frame rate, you might try a higher setting and judge by feel.
- If your frame rate is low or unstable, fixing that will usually do more for responsiveness than raising polling.
Also remember that game engines read input in different ways. Some read the mouse once per frame, so the benefit depends on how the game handles input. Others process input separately from rendering. Because of this, results vary between games and are difficult to predict from the spec sheet. Judge by your own experience rather than by a figure, and do not feel pressured to change the setting just because a mouse offers a higher option. If you cannot tell the difference in a blind test with a friend switching the setting, it is not worth the extra load.
Choosing a Mouse With Polling in Mind
If you are shopping, polling rate should be a minor line on your checklist rather than the headline. Most gaming mice already support the standard rate, and the extra options on some models are a bonus. Before paying more for a high figure, check what else the mouse offers that affects daily use.
Questions to ask before buying:
- Which polling rates does the mouse offer, and on which connection types?
- Can I change the rate without installing software, for example with a button on the mouse?
- Is the setting stored on the mouse, so it stays after I move to another computer?
- Does the battery claim assume the highest rate or a lower one?
- Is the receiver for the top rate included, or is it sold separately?
Compare weight, shape and sensor quality alongside polling. A comfortable shape that fits your grip, a reliable sensor on your mouse pad, and a size that suits your hand will make a bigger difference to your game than a higher number. Budget tiers vary in what they emphasize: entry models usually offer the standard rate and basic software, mid-range options add more rate choices and onboard memory, and premium models may add very high rates and extra tuning. Pay for the features you will use, and check the return window in case the mouse does not feel right.
Getting the Most From the Rate You Already Have
Before changing your polling rate, make sure the rest of the chain is in good shape. Many cases of choppy cursor movement come from something other than the setting. Start with the surface: a dirty or worn mouse pad, or a glossy desk, can cause tracking problems that look like polling trouble. Clean the sensor window and the mouse feet, and try a different surface to see whether the problem changes.
Next, check the computer. A busy processor, background programs and power-saving settings can all cause irregular input. Close unneeded programs, set the power plan to a performance-focused option and keep your graphics drivers and chipset drivers current. For wireless mice, charge the battery, since a low battery can weaken the connection on some models.
A simple routine to try:
- Set the mouse to 1000 Hz and play for a few sessions.
- Note whether movement feels smooth and whether the frame rate holds.
- Change one setting at a time, so you know what caused any difference.
- Record your starting values, so you can return to them.
Be honest about what you notice. Small differences are easy to imagine once you know a setting has changed. If you cannot tell the settings apart in actual play, keep the one that uses fewer resources. Most people end up happiest with a stable, standard configuration and a comfortable mouse.

Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
A Decision Guide by Situation
Polling rate is one of those settings that gets more attention than it deserves, and the right choice depends on what you do with the mouse. The table below pairs common situations with a sensible first choice. It is a guide to thinking, not a rule, and your own comfort should settle the final choice.
| Situation | Reasonable setting | Why |
|---|---|---|
| Office work and browsing | 125 to 1000 Hz | Smooth cursor movement without extra load |
| Casual gaming | 1000 Hz | A widely supported standard with low delay |
| Competitive shooters on a fast monitor | 1000 Hz, or higher if your hardware supports it | Slightly finer tracking if the rest of your system keeps up |
| Wireless mouse used on battery | Lower rates when you need longer battery life | Higher rates generally use more power |
| Older computer or laptop | 500 to 1000 Hz | Leaves processing time for other tasks |
Most people never need to leave 1000 Hz, and many will see no benefit from going higher.
A Short Glossary
- Polling rate: how many times each second the computer asks the mouse for its position, measured in hertz.
- Report interval: the time between those reports. At 1000 Hz it is one millisecond, and at 8000 Hz it is one eighth of a millisecond.
- DPI: dots per inch, a measure of how far the cursor moves for each inch the mouse moves. This is separate from polling rate.
- Input lag: the delay between an action and its effect on screen, which depends on many parts of the system.
- Sensor: the part that tracks movement across the surface.
- Frame rate: how many images your game draws each second.
Why Higher Numbers Do Not Always Feel Different
A higher polling rate shortens the gap between position updates, but your experience also depends on your monitor, game and system. If your display refreshes at a moderate rate, extra mouse updates between each frame may not be visible. Likewise, if a game runs at a modest frame rate, the benefit shrinks. The upper end of polling rates is most relevant when your monitor, graphics card and processor can all keep pace.
There is also a cost to consider. Higher rates ask more of the processor, because it handles many more messages every second, and on some systems that can reduce performance in demanding games. Wireless mice may drain their batteries faster, and some mice turn off certain features at the highest rates. The mouse maker’s software and manual describe which rates are supported and what trade-offs apply.
If you try a higher rate, change one thing at a time, play your usual games for a few sessions and see whether your aim or comfort changes. If nothing improves, return to a setting that is stable and efficient.
How to Read a Mouse Listing for Polling Information
Product pages tend to highlight the maximum polling rate, but the details are often elsewhere. Look for whether the maximum applies in wired mode only or also wirelessly, and whether it needs a special receiver or dock. Check whether the rate can be changed in the maker’s software, or whether you must use a button on the mouse. Look at which versions of Windows or other computer systems the software supports.
Pay attention to the sensor and weight too, because these influence feel more than polling rate does. A comfortable shape that fits your grip will matter far more in practice than the headline hertz figure. If you are unsure, look for owner comments that discuss battery life and stability at different rates.
When to Follow the Maker and When to Troubleshoot
If your cursor stutters, skips or freezes after changing the rate, go back to a lower setting and check that your drivers and the mouse firmware are up to date from the official source. Connect the mouse to a different port, and avoid hubs while testing. Follow the maker’s instructions for firmware updates, since interrupting an update can cause problems. If the issue continues, contact the maker’s support with your model number and the steps you tried.
Keeping Your Setup Simple and Stable
Most mouse problems blamed on polling rate turn out to be caused by something else, such as a dirty sensor, a worn mouse surface, a weak wireless connection or a busy computer. Before you chase a higher number, spend a few minutes on the basics. Wipe the sensor window gently, use a clean mouse pad with a consistent texture, and keep the receiver of a wireless mouse close to the mouse, ideally on a short extension cable on the desk rather than behind the computer.
Check your power settings as well. Laptops and some desktops reduce performance to save energy, which can make the cursor feel uneven. Close unneeded programs while you play, and keep your graphics drivers current from the official source. When you find a combination that feels good, leave it alone, and make a note of the settings so you can restore them after an update.
Polling Rate in Real Games: What Changes and What Does Not
It helps to separate what polling rate can influence from what it cannot. Polling rate affects how fresh the position data is when the computer reads it. When you flick the mouse across the pad, the computer builds your crosshair movement from a stream of position reports. With more reports per second, that stream is denser, so the path the cursor or crosshair follows can look smoother and the most recent report is, on average, closer to where your hand actually is at that moment. That is the whole benefit, and it is a real one, but it is also a narrow one.
Polling rate does not change how far the cursor travels for a given hand movement. That is set by DPI and sensitivity. It does not change how accurately the sensor reads the surface, how the mouse handles fast acceleration, or whether the shape fits your hand. It also does not fix problems elsewhere in the chain: a slow monitor, a game running at a low frame rate, or a congested wireless connection can each hide whatever small gain a higher polling rate offers. Players sometimes raise the polling rate, feel no difference, and conclude the setting is broken, when in fact another part of the setup is the limiting factor.
The games where dense reporting is most likely to be noticeable are fast first-person shooters played at high frame rates on high-refresh monitors, where crosshair movement is constant and small corrections matter. Slow-paced strategy games, turn-based games and everyday desktop work place far less demand on the reporting stream, and most people cannot distinguish rates there at all. Even in shooters, the difference shows up mainly in the smoothness of tracking motion rather than in reaction time, because human reaction time is far larger than the gaps between reports at any common rate.
A simple way to test on your own setup
If you want to judge for yourself, change one variable at a time. Set a rate, play the same game mode on the same map for a full session, then switch and repeat on another day when you are similarly rested. Avoid judging from a single round, because confidence, warm-up and opponents all vary more than the setting does. Many players find that what they first notice after switching is not the rate itself but the placebo of having changed something, and only back-to-back sessions in a controlled aim trainer give a fair impression. Keep notes on how tracking felt during long strafing fights rather than on flick shots, since sustained tracking is where report density matters most.
Polling Rate and the Rest of the Latency Chain
Think of the path from hand to screen as a chain of small delays. The sensor reads the surface, the mouse firmware packages the data, the report waits for the next polling moment, the operating system and game engine process the input, the game renders a frame, and the monitor displays it. Polling rate shortens only one link in that chain: the wait for the next report. Every other link stays the same, which is why doubling or multiplying the rate produces a smaller total improvement than the headline numbers suggest.
This is also why the benefit depends on frame rate. If the game renders a new frame less often than the mouse reports, several reports are effectively bundled into one frame and the extra freshness is partly wasted. When frame rate and monitor refresh are high, each frame can use newer data, and a higher polling rate has more room to help. Players on modest hardware often gain more from lowering graphics settings to raise frame rate than from raising polling rate, because the frame interval is the bigger delay in their chain.
Where the CPU fits in
Every report is an interrupt the processor has to handle. At the rates used by ordinary mice this cost is trivial, but at the highest rates the interrupt load becomes measurable, especially on older processors or laptops running on battery-saving power plans. Symptoms of a system struggling include frame-time spikes in games that otherwise run smoothly, or audio crackle in setups that are sensitive to interrupt load. If you see those symptoms after raising the rate, step down one level and test again; the practical difference in feel is small, while stutter is immediately obvious and far more damaging to aim.
How Polling Interacts With DPI, Sensitivity and Grip
Polling rate and DPI are often confused because both are headline numbers on the box, but they do different jobs. DPI describes how many counts the sensor reports for each inch of movement. Polling describes how often those counts are delivered. A useful way to picture it: DPI is the resolution of the ruler, polling is how often someone reads the ruler aloud. Raising DPI without changing sensitivity makes the cursor travel farther for the same movement; raising polling does not change travel distance at all.
There is one interaction worth knowing. At very low DPI, a slow hand movement may produce only a count or two between reports, so motion can look steppy at any polling rate. At moderate to high DPI, each interval contains more counts and movement looks finer-grained. Some players therefore prefer a higher DPI paired with a lower in-game sensitivity, which keeps the same overall turning speed while feeding the game denser data. The trade-off is that very high DPI can feel twitchy on the desktop and in menus, so many players use per-profile DPI settings: one for the desktop, one for games.
Grip and movement style matter too. Fingertip and claw players make many small corrections, and dense reporting describes those corrections more faithfully. Palm players who make broad arm sweeps produce smoother, slower data that even a modest rate captures well. Neither style is better; the point is that the value of a high rate depends on the movements you actually make, not just on the games you play.
Wireless Polling in Practice
Modern gaming wireless mice use a dedicated receiver and a proprietary radio link rather than standard Bluetooth, and they can sustain high polling rates that older wireless mice could not. The receiver’s placement matters more than most people expect. A receiver plugged into the back of a tower case under a desk has to work through metal, wood and distance, while the same receiver on a short extension cable near the mouse pad gets a clean signal. Many wireless mice ship with exactly such an extension adapter, and using it is the single easiest reliability fix available.
Interference is the other practical factor. Routers, other wireless peripherals and USB 3 devices and cables can all add noise near the receiver. If a wireless mouse stutters at a high polling rate but feels fine wired, suspect the radio path before suspecting the sensor: move the receiver closer, move it away from other transmitters, and test again. Battery life also falls as polling rises, because the radio wakes and transmits more often. Players who dislike charging often settle on a middle rate for daily use and switch to the highest rate only for competitive sessions, which profiles in the maker’s software usually make painless.
Bluetooth is a different case
Bluetooth connections are designed for power saving and convenience, not for dense reporting, and their effective report rates are far lower than a gaming receiver or a cable. That is fine for office work, travel and casual games, and it is why many gaming mice offer both modes: Bluetooth for the workday, the gaming receiver or a cable for play. If a mouse feels laggy in Bluetooth mode during a fast game, that is expected behaviour rather than a fault.
A Sensible Setup Routine
Start from a known-good baseline. Connect the mouse directly to the computer, or place its receiver close to the pad with the extension adapter. Update the maker’s software and firmware if an update is offered, then set DPI to the value you already like before touching polling. Change polling one step at a time, testing each step in the game you play most, and watch for stutter or frame-time problems as carefully as you watch for smoothness. If a step causes problems and the previous step felt the same in normal play, stay at the previous step without regret.
Save your chosen settings to the mouse’s onboard memory if it offers it. Onboard memory means your rate and DPI travel with the mouse to another computer, a laptop or a console without the software installed. It also protects your settings from being reset when software updates or when you reinstall your operating system. Finally, re-check after big changes elsewhere: a new monitor with a higher refresh rate, a major game update or a new PC can all shift which rate feels best, because they change the other links in the chain.
Common mistakes when chasing high rates
The most common mistake is testing through a cheap unpowered hub or a front-panel port with an internal cable run, then blaming the mouse for inconsistent results. Another is changing DPI, sensitivity and polling all at once, which makes it impossible to know what helped. A third is assuming a test website’s peak reading is your real rate: those tools report what your movement produces, and slow or uneven movement under-reports. Move the mouse in fast, steady circles for a fair reading, and treat the tool as a rough check rather than a laboratory measurement. The last mistake is leaving the rate at maximum on a laptop you also use for work, draining the battery for a benefit you cannot perceive in a spreadsheet.
Polling Rate for Different Kinds of Players
Competitive shooter players on high-refresh setups are the audience the highest rates were built for, and they are the most likely to notice smoother tracking. Even for them, shape, weight and sensor quality should come first when choosing a mouse, with polling as a supporting feature. MMO and MOBA players, whose mice spend as much time clicking abilities as tracking targets, gain little from extreme rates and may prefer to spend on buttons, comfort and battery life instead. Strategy and simulation players are served perfectly well by standard rates, and creators who split time between editing timelines and casual games will notice a good shape and reliable clicks far more than report density.
For families and shared computers, simplicity wins: set a mainstream rate that every game handles well, store it onboard, and forget the setting exists. The honest summary of the whole topic is that polling rate is a finishing touch on an already good setup. Get the mouse that fits your hand, set a DPI you can control, keep the connection clean, and then let polling be the last small optimisation rather than the first buying criterion.
How Games and Operating Systems Handle the Reports
Not every game uses incoming mouse data in the same way. Many modern shooters offer a raw input option, which takes the mouse data directly and bypasses operating-system pointer settings such as acceleration. Raw input is generally the cleaner path for gaming, because what the game receives matches what the mouse sent, and your polling and DPI settings behave the same regardless of desktop pointer options. If a game lacks raw input, the operating system’s pointer speed and any enhance-pointer-precision style setting sit between the mouse and the game, and they can change the feel more than polling ever will. Checking that one setting is worthwhile before experimenting with rates.
Some engines also process input on their own schedule. A game may sample the latest mouse position once per frame, once per physics tick, or through a buffered queue, and two games at the same frame rate can therefore feel slightly different at the same polling rate. This is why advice from one game’s community does not always transfer to another title, and why your own testing in the game you actually play beats general charts. It also explains why a rate that feels perfect in one shooter can feel unremarkable in a slower game: the slower game’s other systems update less often, so fresher mouse data waits longer to be used.
High polling and older games
Older titles were built when standard rates were the norm, and a few handle very high report rates poorly, showing jitter, uneven turning or unusually high CPU use in menus. If a classic game misbehaves after you raise the rate, lowering the rate for that game’s profile is a practical fix rather than a compromise you should feel bad about. Per-game profiles exist for exactly this reason: the mouse can run at its highest rate in your main competitive title and at a modest rate everywhere else, switching automatically when the game launches.
Reading Specs Without Being Misled
Listings present polling as a single maximum number, but the useful questions are more specific. Is the maximum available over a cable, over the wireless receiver, or both? Some mice reach their headline rate only when wired, or only with a separate enhanced receiver, while the included receiver runs at a lower maximum. Does the rate hold steady during fast movement, or is it a peak the mouse touches briefly? And can the rate be changed in onboard profiles, or only while the maker’s software is running? The answers decide whether the number on the box describes your actual setup.
Also separate polling from the other latency claims on a listing. Switch response, wireless transmission and sensor processing each contribute their own small delays, and a mouse with a moderate polling rate but a well-designed overall pipeline can feel as responsive as one advertising a higher rate. Chasing the single biggest number is less reliable than choosing a mouse whose shape, weight, clicks and sensor you like, from a maker whose software lets you set and store the rate you want. The spec sheet is a starting point for questions, not a ranking.
A note on testing tools
Browser-based polling testers are convenient but limited: the browser itself, the operating system and your movement pattern all shape the result, and readings fluctuate from run to run. Use them to confirm a setting took effect and to spot gross problems, such as a mouse stuck at a low rate through a faulty hub. Do not use them to argue about small differences between runs, and repeat any test a few times before drawing a conclusion. A wired connection directly to the computer, with steady fast circular movement, gives these tools their fairest chance.
When to leave the setting alone
Sometimes the right decision is to change nothing. If your mouse feels responsive, your games run smoothly and you are not chasing a specific problem, the standard rate your mouse shipped with is already well matched to most monitors and most games. Settings exist to solve problems and to fine-tune a setup you know well; changing them out of obligation, because a forum thread insisted everyone must, often leads to a week of second-guessing your aim for no gain. Learn what the setting does, try it properly if you are curious, and then keep whichever configuration lets you forget about settings and play. That confidence is worth more than a spec number, and it is the real destination of every adjustment this guide describes: a mouse that disappears under your hand so your attention stays on the game.
Frequently Asked Questions
What polling rate should I use?
1000 Hz for most gaming.
Does a higher polling rate drain battery?
Yes, on wireless mice.
Will 8000 Hz improve my aim?
Probably not noticeably.
Does polling rate affect input lag?
A higher rate shortens the time between reports, which can slightly reduce delay in that one step. Total latency also depends on the sensor, connection, game and display, so the overall effect is often small.
Is 8000 Hz worth it for casual players?
Usually not. The standard 1000 Hz rate is smooth enough for most people, and higher rates can add processor load and drain wireless batteries faster.
Can a high polling rate cause stutter?
It can on some systems, especially older or busy processors, because the computer handles many more reports each second. If you see stutter, drop to a lower rate and test again.
Why is my polling rate lower in a test than in the software?
Tests depend on how smoothly you move the mouse, and the result can also be limited by the port, hub or background software. Try plugging directly into the computer and moving in steady circles.
Is polling rate the same as report rate?
Yes, the terms usually describe the same thing, which is how often the mouse sends its position to the computer. Some makers use different names, so check the manual.
Does polling rate change how far the cursor moves?
No. Distance is set by DPI and your in-game or operating system sensitivity. Polling rate only changes how often the position is reported.
Should I use a lower rate to save wireless battery?
It can help. If you do not notice a difference at a lower rate, you may get longer use between charges. Check the maker's battery notes for how the rate affects runtime.
Do USB hubs affect polling rate?
Some hubs and long extension cables handle high rates poorly. Connect the mouse or its receiver directly to the computer when you test.
Bottom Line
Use 1000 Hz and move on unless you have a reason to change it. See our gaming mouse buying guide.
Related Reading
- 6 Best Gaming Mice Under $50
- 6 Best Gaming Keyboard and Mouse Combos for PC
- 6 Best Gaming Mice for FPS: Valorant, CS, Fortnite and Warzone
- 6 Best Hard Gaming Mouse Pads: Plastic, Glass and Polycarbonate
- Best Mouse Grip for Gaming: Palm, Claw and Fingertip Explained
More Gaming Mouse Guides
- Gaming Mouse Buying Guide
- Best Wireless Gaming Mice
- Best Lightweight Gaming Mice
- Best Mouse DPI for Gaming



