Disclosure: As an Amazon Associate, reviewstook.com earns from qualifying purchases. Links to Amazon on this page are affiliate links; they cost you nothing extra.
Most soundbars connect by HDMI ARC, optical or Bluetooth.
Last updated: October 31, 2026.

HDMI ARC or eARC
Plug the HDMI cable into the TV ARC port and the soundbar ARC port. See soundbar cables.
In this guide
Optical
Use a Toslink cable if there is no ARC. Atmos is not supported.
Bluetooth
Pair from the TV settings; expect some delay.
Settings
Set TV audio output to external speaker or HDMI ARC and enable CEC if needed.
Before you start: check your ports
Take a minute to look at the back of your TV and your soundbar. Find the HDMI ports on the TV and look for a label such as ARC or eARC. Only the labeled port carries audio back to the soundbar. Then check the soundbar for an HDMI output labeled the same way, an optical input and any other inputs, such as aux or USB.
Check your cables. You need an HDMI cable for ARC or eARC, a Toslink cable for optical, or a 3.5 mm cable for a basic analog connection. A soundbar often comes with one cable, but it may not be the type you need. Read the manual to see what is included. Make sure the HDMI cable is long enough to reach without strain, and avoid sharp bends at the plug.
Power both devices and keep the remotes handy. Plug the soundbar into a wall outlet or a surge protector, and give it space for ventilation.
- TV has ARC or eARC: use HDMI first.
- No ARC: use optical.
- Older TV: try analog if the soundbar has an input.
Note which input names your TV uses, so you can find them in the menu later.
Placing the soundbar and subwoofer
Where you put the soundbar changes how it sounds. Place it centered under the TV, as close to ear level as practical, and pointing toward the seating area. Make sure it does not block the TV’s remote sensor. If the soundbar is taller than the stand gap, check whether it blocks the bottom of the screen.
For wall mounting, follow the manual and use the right hardware and a stud or suitable anchor. Check weight limits and do not guess. Some bars come with a template to mark holes.
If you have a wireless subwoofer, plug it in and let it pair. Place it near the front of the room first, then move it to find the spot where bass sounds tight rather than boomy. Corners tend to boost bass and can make it muddy. Avoid placing the sub inside a closed cabinet.
Keep power cables away from audio cables to reduce interference, and keep the bar away from walls that may reflect sound in an unwanted way. Rear speakers, if included, go behind or beside the seating position, so plan outlets or wireless pairing.
Take care when moving gear, and keep boxes for returns until you are sure it works.
Setup menus and sound modes
After the physical connection, open the TV sound settings. Choose the audio output option that matches your connection, such as HDMI ARC, optical or external speaker. Turn off the TV speakers if the menu does not do so automatically. If you hear sound from both, check this setting.
Next, look at the audio format. Some TVs offer options like automatic, PCM or passthrough. Automatic is usually the easiest choice. If you have trouble with surround formats, check the manual for the right setting. For Atmos or other advanced formats, check that your source device, app and TV all support passing the audio through.
On the soundbar, explore the modes. Common options include movie, music, voice or dialog, night and bass boost. Night mode reduces loud peaks, which is useful late in the day. Voice modes can make speech easier to hear. Try each mode with content you know well and pick what sounds natural.
Use the bar’s app or display if there is one. Some bars have an app for firmware updates and equalizer controls. Keep the firmware current by following the maker’s instructions.
Adjust volume levels so that the TV remote controls the bar if possible.
One remote and HDMI CEC control
Many people prefer to control the soundbar with the TV remote. HDMI CEC lets connected devices share control signals so that the TV remote adjusts the soundbar volume and powers it on or off with the TV. The feature has different names on different brands, so look in the TV menu for terms related to HDMI control or device link and enable it.
If CEC does not work, check that it is enabled on both the TV and the soundbar, and that the bar is on the labeled ARC port. Power cycle both devices. Some setups also work with an infrared learning feature or a code entry on the TV remote. Check the manual for options.
CEC can sometimes cause odd behavior, such as devices turning on unexpectedly. If that happens, adjust or disable the feature for the device that is misbehaving.
If you use a streaming device or console, connect it to the TV or the bar depending on your manual. When connecting devices to the bar’s HDMI input, check that it passes the video formats you use.
For best results, keep all devices updated with their latest software, following the maker’s steps.
Troubleshooting common problems
Most connection problems come from a few causes. If there is no sound, check that the bar is on the correct input, the TV output is set to the right option, the cable is firmly seated and the volume is up on both devices. Try a different HDMI port or cable if the issue continues.
If audio is out of sync with the picture, look for an audio delay or lip sync setting in the TV or the bar. Wireless connections tend to add more delay, and wired connections are usually better for video. Some bars offer a sync adjustment in the app.
If sound cuts out, the cable may be loose or poor quality, or the devices may be handshaking incorrectly. Power everything off, unplug for a short time, and restart in order: TV first, then bar.
If dialog is quiet, try a voice mode or reduce the bass. If you hear hissing or buzzing, move power cables away from signal cables and check for ground loop issues.
- Try another input on the TV.
- Check the audio format setting.
- Update firmware.
- Reset to factory settings as a last step, following the manual.
If nothing helps, contact the maker’s support with model numbers ready.
What ARC and eARC Actually Change
ARC stands for Audio Return Channel. It lets the TV send sound back to the soundbar through the same HDMI cable that carries video to the TV, so one cable does both jobs. eARC, the enhanced version, has far more bandwidth. That extra room allows uncompressed and high-bitrate audio formats, including lossless surround and object-based formats, to pass from the TV to the soundbar.
For many households, ordinary ARC is plenty. It handles stereo and compressed surround such as standard Dolby Digital. You gain from eARC when the soundbar and the TV both support it, and you play content with high-quality lossless audio from a source connected to the TV. If either device lacks eARC, the connection falls back to ARC, and that is usually fine for streaming apps.
Some points to check in the manuals:
- Which HDMI port on the TV is labeled ARC or eARC. Usually only one is.
- Whether the soundbar lists ARC or eARC on its HDMI output.
- Whether the soundbar lets you pass video through from other devices to the TV.
- Whether the TV can send the format you want, such as Dolby Atmos, over its ARC port. Some TVs convert or limit formats.
Cable choice rarely needs to be dramatic. A certified high-speed or ultra high-speed HDMI cable of reasonable length works for most setups. For eARC, the cable should be rated for the bandwidth, so check the packaging or the maker’s guidance. A cable from a reputable seller with a clear specification is a safer choice than an unlabeled one.
Connecting Consoles, Streamers and Players
Soundbars are only part of a living room system. A game console, a streaming stick and a disc player all need somewhere to plug in. There are two common approaches, and the right one depends on your hardware.
The first approach is to connect every device to the TV and then send audio to the bar through ARC or eARC. This is simple and works for most people. The TV handles input switching, and the bar only sees what the TV outputs. The limit is that the TV decides which audio formats are passed along, and some TVs reduce multichannel sound to a simpler format.
The second approach is to connect devices to the soundbar’s HDMI inputs, if it has them, and then connect the bar to the TV’s ARC port. The bar receives the original audio, which can help with advanced formats. Check that the bar passes through the video features you use, such as high refresh rates, HDR and variable refresh rate for gaming. Not every bar supports all of them, and one weak link can switch features off.
For gaming, input lag matters. A wired connection is best, and some bars and TVs have a game mode or low-latency setting. If you hear a delay between button press and sound, try that mode or look for an audio sync adjustment. Keep in mind that you can also route console sound through a headset and leave the bar for shared play.
Whichever method you choose, label your inputs in the TV menu so family members know where to find each device. Update each device’s software following the maker’s instructions, since firmware often fixes handshake problems.
Wi-Fi, Apps and Multi-Room Features
Many modern soundbars connect to your home network. The benefits include firmware updates, streaming music directly from services, voice assistant support and linking with other speakers in the home. The setup usually happens in the maker’s app: install it, follow the pairing steps, choose your Wi-Fi network and give the bar a name.
A few practical tips help:
- Use the 2.4 GHz or 5 GHz band that the manual recommends, and keep the bar within reasonable range of the router.
- If setup fails, temporarily move the bar closer, restart the router and try again.
- Keep your phone on the same network during setup.
- Use the app to turn on automatic updates if the option exists.
Streaming over Wi-Fi sends sound straight to the bar and bypasses the TV. That is convenient for music, but your TV and the bar can then show different volume levels. Learn which input the bar is set to at any moment. If something plays unexpectedly, check whether the bar has switched to its network source.
Multi-room features link several speakers so they play the same track or different ones. Some ecosystems let you add rear speakers or a subwoofer wirelessly. Compatibility depends on brand and model, so check the maker’s list before you buy additions.
Wall Mounting Step by Step
A wall-mounted bar can look neat and free up the stand. It also carries risks if done wrongly, so go slowly and follow the instructions that came with your soundbar and the mounting hardware.
- Check the bar’s weight and the weight rating of the bracket and fixings. Never go beyond the stated limit.
- Use the template or paper cutout to mark the hole positions. Hold it against the wall with tape and confirm the position with a level.
- Find wall studs with a stud finder when possible, or choose anchors rated for the wall type and the load. Drywall alone is a weak base for heavy items.
- Before drilling, check for hidden electrical wires and pipes using suitable detection methods, and follow local codes.
- Drill pilot holes, insert anchors if needed and attach the brackets. Tighten snugly without overtightening.
- Hang the bar and check that it is secure and level before letting go fully.
Plan the cable run beforehand. Power cords and HDMI cables should reach without tension, and any in-wall routing must follow electrical codes and use cables rated for in-wall use. If you are unsure, hire a licensed professional. Leave a gap below the TV so the bar does not block the remote sensor or the bottom of the picture.
Tuning Dialogue, Bass and Volume
When everything is connected, spend a few minutes tuning. Choose a familiar movie scene or music track and sit where you normally sit. Set the bar’s volume to a comfortable level and then adjust the subwoofer level up or down in small steps until bass supports the sound without drowning out voices.
Dialogue clarity is a common complaint. Try a speech or dialog mode, reduce the bass slightly and raise the center channel level if the bar offers that control. Late-night viewing is easier with a night mode that tames loud effects. If volume jumps between apps, look for a loudness or auto-volume setting.
Room acoustics matter too. Hard surfaces make sound brighter, while rugs, curtains and furniture soften it. If voices sound harsh, add soft furnishings. If bass booms, shift the subwoofer slightly or turn the level down. Make changes one at a time so you can hear what each one does.
Quick Checks Before You Call It Done
Run a short test before putting the remotes away. Play content with a clear left and right pan, such as a nature program or a demo clip, and confirm the sound moves across the room. Test each input you use, including the streaming app, any console and cable or antenna TV. Turn the TV off and on again to confirm the bar wakes with it, and try the remote for volume and mute.
Then check the small things. Make sure the subwoofer is paired and not buzzing, the cables are not pulled tight and the bar sits level. Write down the model numbers and keep the manual or a link to it. If a problem returns later, you can tell the maker exactly what you tried.
Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
Working Through the Connection Methods Like a Technician Would
Most soundbar connection problems are solved by method rather than by new equipment. This section adds a calm, ordered way of working that sits alongside the step-by-step guidance above, so that when sound is missing, delayed or controlled by the wrong remote, you can find the cause without randomly changing settings on both devices at once.
Prove Each Link in the Chain, One at a Time
Think of the setup as a chain: the source produces the sound, the television passes it on, the cable carries it and the bar plays it. When something fails, test the chain in order instead of guessing. Start by confirming the bar plays anything at all, using a phone or another simple source if your bar allows it. Then confirm the television produces sound through its own speakers with the bar disconnected, which proves the source and the television. Then reconnect one cable, select the matching input on both devices and test again with ordinary broadcast television before testing apps or consoles. Each step either clears a link or identifies the one that is broken, and you never end up unsure which change fixed the problem.
Settings that most often break an otherwise correct installation
Three settings cause a large share of call-outs and returns. The first is the television audio output, which may still point at the internal speakers even though a cable is connected. The second is the format setting, where a television set to pass a format the bar cannot handle can produce silence where a simpler setting would produce sound immediately. The third is the control feature that links power and volume between devices, which lives under different names on different brands and is often switched off by default. Change these one at a time, in that order, and re-test after each change. Resist the factory reset until this short list has been worked through, because a reset usually returns you to the same defaults that caused the trouble.
Adding Consoles, Players and Streamers Without Breaking What Works
Once television sound works, add extra devices one at a time and test after each addition. Decide deliberately whether each device should connect to the television or directly to the bar, based on which arrangement passes the formats that device produces and keeps switching simple for the household. After each addition, check three things: that the picture reaches the screen, that the sound reaches the bar without a distracting delay, and that the remote you expect to use still controls the volume. If a new device breaks an older one, undo only the last change. That discipline keeps a growing setup understandable instead of turning it into a knot nobody wants to touch.
Keeping the Installation Reliable Over Time
Connections drift. Cables get knocked during cleaning, televisions receive updates that change menu defaults, and bars get unplugged and reconnected to the wrong socket. Build a small safety net: label both ends of each cable, photograph the rear connections once everything works, and keep a short note of the television settings you changed. When a fault appears months later, compare the setup with the photograph and the note before changing anything. In most homes that comparison finds the problem in minutes, whether it is a cable in the wrong port, an input changed by a guest, or a setting reset by an update.
When the Problem Really Is the Equipment
Sometimes methodical testing does prove a hardware fault: a port that never works with any cable, a bar that drops sound on every source, or a television that cannot pass sound it claims to support. Reach that conclusion only after the same fault has followed the suspect device through cable swaps and source swaps. Then use the manufacturer support route with your test notes ready, because a clear description of what you have already tried shortens any repair or replacement conversation considerably. Until that point, assume the setup is fixable, because in the great majority of homes it is.
More Practical Guidance Before You Decide
Listen in the room you actually use, not in a showroom mindset
A soundbar that impresses in a short demo can feel different across a full evening of mixed content, so judge any pick in this list by how it handles the handover between quiet dialogue, a sudden action peak and then music under the closing credits. Keep the volume where you normally watch and pay attention to whether you keep reaching for the remote. If you are constantly riding the volume control, the balance between voices and effects is wrong for your room, no matter how exciting the loud moments feel. Small adjustments to placement and to the dialogue or night settings usually matter more at that point than swapping to a different bar altogether.
Why placement changes the result more than most settings
Soundbars fire sound forward into the room, so whatever sits in front of them shapes what you hear. A bar pushed to the back of a deep shelf, hidden behind the lower edge of the television or tucked inside a cabinet with a closed front will sound muffled even if it performed well in open air. Give the drivers a clear line into the room, keep the front edge of the bar close to the front edge of the furniture, and leave space at the sides where the design expects it. If your bar uses upward-firing drivers, the ceiling becomes part of the system, so a clear path upward matters just as much as the space in front.
A simple first-week routine that settles a new bar in
During the first week, resist the urge to change every setting at once. Start with the standard sound mode, set the bass to a neutral level and watch the kind of programmes you watch most. Change one thing at a time on the following nights: try the dialogue setting on a drama, the night setting after others have gone to bed, and the music setting with a familiar album. Note which changes you keep. That short, patient routine tells you more about whether a pick suits your household than any single test clip, and it prevents the common trap of judging a bar on settings you would never use again.
Care and cleaning that keep a bar sounding consistent
Dust settles on speaker grilles and inside the small gaps around buttons and ports, and over time a heavy build-up can dull the top end and make controls feel sticky. Wipe the cabinet and grille gently with a dry or very slightly damp soft cloth, keep sprays away from the drivers, and check the rear ports occasionally so cables sit fully home. Keep the bar out of long periods of direct sunlight and away from radiators, because heat and ultraviolet light age plastics and adhesives. If the bar has a separate subwoofer, give its driver the same gentle treatment and keep its port free of household clutter.
How to compare two bars fairly at home
When you are torn between two picks in this guide, compare them on the same scenes, at matched loudness, from your normal seat. Louder almost always sounds better in a quick comparison, so take a moment to level-match by ear on a dialogue passage before judging tone. Listen for three things: whether voices stay clear when music and effects join in, whether bass supports the scene without booming on male voices, and whether the sound stays comfortable over a long episode rather than fatiguing you. The bar that wins on those everyday tests is usually the right choice, even if the other one produces a bigger first impression.
Room features that help or hurt any soundbar
Hard, bare rooms with wooden floors, large windows and little soft furnishing reflect sound and can make any bar seem harsh or echoey, while heavily furnished rooms absorb energy and can make the same bar feel restrained. You cannot rebuild the room around a soundbar, but small changes help: a rug between the bar and your seat, curtains drawn during films, and keeping the bar away from a corner where bass builds up unevenly. Mention your room honestly when you weigh the picks above. A compact bar in a small, soft room often delivers a more satisfying result than a large bar fighting a big, reflective space.
When to troubleshoot settings before blaming the hardware
Many complaints about thin sound, weak bass or unclear voices trace back to a setting in the television rather than to the bar itself. Check that the television is sending the format the bar expects, that any downmix or night compression in the television menu is not fighting the bar settings, and that the correct input is selected after switching sources. Work through one change at a time and re-test with the same scene. Only when the settings on both devices agree and the problem remains is it sensible to conclude that the pick itself is a poor match for your room or your content.
Thinking about the household, not just the main viewer
A soundbar serves everyone in the room, and the best pick for the person in the centre seat may not suit a partner who sits to the side, children who watch at lower volume, or a family member who mainly listens from the kitchen doorway while cooking. Consider viewing angles, typical volume and how often the bar will be used for music or sport rather than films. Picks with clear dialogue modes and forgiving wide dispersion tend to please mixed households, while a bar tuned purely for cinematic impact can leave everyday television feeling overblown. Match the pick to the household pattern, not to a single ideal film night.
Real-World Scenarios and Long-Term Ownership
Scenario: film nights in a family living room
Picture a typical Friday evening: children on the floor, adults on the sofa, a film that swings between whispered conversation and loud set pieces. In that setting the winning qualities are balance and forgiveness. Voices must stay clear without anyone guarding the remote, bass must support the action without shaking the room during dialogue scenes, and the bar must behave identically whether the film comes from a streaming app, a broadcaster or a player. When you read the picks above with this scenario in mind, favour the models described as composed and easy to control over those described as dramatic, because drama is easy to add with volume while composure cannot be added afterwards.
Scenario: sport, news and daytime television
Daytime and sports viewing make different demands from films. Commentary needs to sit clearly above crowd noise, news presenters need to stay intelligible at modest volume while the household moves around, and the sound should remain comfortable for hours rather than impressive for minutes. Bars and speakers with a forward, clear presentation suit this pattern best, and a dialogue setting that works well at low volume is worth more here than any surround effect. If this is most of your viewing, weight the sections of this guide that discuss speech and everyday settings heavily, and treat cinematic scale as a pleasant extra rather than the deciding factor.
Scenario: gaming through a soundbar
Games reward a setup that keeps effects, music and voice chat in balance for long sessions at close range. Explosions that impress in a film can fatigue during an evening of play, and any noticeable delay between action and sound becomes distracting far sooner than it does with passive viewing. Keep the connection path as direct as your equipment allows, use the sound mode that sounds most natural rather than the most processed, and set volume for comfort across a whole session instead of for the loudest moment. Players who share the room with others should also value good low-volume clarity, because most gaming happens while the rest of the household is awake to something else.
Scenario: music as a serious second job
Many bars spend as many hours playing music as television, yet buyers often test only film clips. A bar that handles music well keeps vocals natural, separates instruments without harshness and produces bass that follows the rhythm instead of booming over it. Try familiar tracks when you compare the picks, including one quiet acoustic piece and one busy, produced recording, and listen from where you actually sit or stand while music plays, which is often not the centre seat. If music matters equally with television in your home, let that test carry real weight, even if it means choosing the more balanced pick over the more cinematic one.
Living with neighbours, thin walls and shared spaces
In flats and terraced homes, the best soundbar is partly a social decision. Bass travels through structures in a way that voices do not, so a setup that sounds modest in your room can still disturb the home below or beside you. Favour picks and settings that keep dialogue clear at lower overall volume, use night settings without embarrassment, and place any subwoofer away from shared walls and off bare floors where a mat or furniture can soften transmission. A courteous setup that you can enjoy at any hour is worth more than a powerful one you feel obliged to keep turned down and apologetic.
Upgrading later without starting again
A soundbar purchase does not have to be the end of the system. Some owners later add rear speakers, move the bar to a second room when they upgrade the main set, or hand it on to a family member with a smaller television. When you compare the picks, consider which one would still make sense in that second life: a versatile bar with common connections and simple controls adapts to a new room far better than a highly specialised model. Keep the box, the remote and any brackets and feet you did not use, because a complete kit moves rooms, and homes, far more gracefully than a bare bar with missing parts.
Understanding warranties, support and everyday reliability
Soundbars are simple products, but remotes fail, ports get damaged and software occasionally needs attention. Before you buy, check how the maker supports the product in your country, whether replacement remotes are easy to obtain, and whether firmware can be updated without specialist help. Register the product if the maker offers it, keep proof of purchase with the manual, and note the exact model name somewhere you can find it later, because support conversations go far faster when you can name the product precisely. These dull details rarely decide between two similar picks, yet they decide how painless ownership feels in year three.
A note on volume, hearing comfort and long sessions
Any system that makes sound clearer also makes it easy to listen louder than intended, especially during action films and games. Keep long sessions at a level where you could still hold a conversation without raising your voice, take breaks during marathon viewing, and be particularly careful with children, who will happily sit close to a loud bar for hours. Clarity should be doing the work, not volume: if you find yourself turning a new setup up week after week to achieve the same satisfaction, revisit placement and settings instead, and consider whether the room or the pick itself needs attention.
Further Notes for Confident Buying and Ownership
How sound changes as you move around the home
Television sound is rarely enjoyed from one perfect seat alone. People listen while cooking, ironing, working at a table or drifting in and out of the room, and a setup that only impresses from the centre cushion is less useful than it first appears. Walk around during a familiar programme after installing any pick from this guide and notice where voices stay clear and where they fade. You cannot make every corner perfect, but small changes in bar position, angle and balance can widen the area that works well. Households that value that everyday coverage should favour forgiving, balanced picks over narrowly focused ones.
Why the first impression of a new setup often misleads
New audio equipment almost always sounds startlingly different on the first evening, partly because it is different and partly because you are listening harder than usual. Brightness can feel like clarity, strong bass can feel like quality and sheer loudness can feel like improvement. Give the setup several days and a range of ordinary content before judging it, and keep returning to the same test: can you follow speech effortlessly at your normal volume, and can you listen for a whole evening without tiredness. Picks that pass those quiet tests are the ones owners still praise a year later, long after the first-evening excitement has faded.
Keeping remotes, inputs and household sanity in order
The most-used feature of any television setup is the one that causes the least friction. Decide which remote runs the volume, teach everyone in the household that single routine, and put the other remotes in a drawer rather than in competition on the sofa. Label inputs in the television menu where the set allows it, so the correct source has a recognisable name instead of a number nobody remembers. When guests or children change something, a calm return to that known routine fixes most confusion. The picks in this guide all reward this kind of order, because none of their benefits matter if the household dreads switching the system on.
Frequently Asked Questions
Why no sound?
Check TV audio output.
Which cable?
HDMI ARC or eARC.
Does optical do Atmos?
No.
How do I know which HDMI port is ARC?
Look for a label such as ARC or eARC next to the port on the back of the TV. If it is unclear, check the TV manual. Only the labeled port carries audio back to the soundbar.
Why do I hear sound from both the TV and soundbar?
The TV speakers may still be on. Open the sound settings and select the external speaker or HDMI ARC output, or turn off the internal speakers.
Why is the audio delayed behind the picture?
Wireless connections and processing can add delay. Look for an audio sync or lip sync setting on the TV or bar, and use a wired connection if possible.
Can I control the soundbar volume with the TV remote?
Often yes, through HDMI CEC or an infrared learning feature. Enable the feature on both devices and check the manuals for the exact steps.
Where should I place the subwoofer?
Start near the front of the room, then move it until the bass sounds tight rather than boomy. Avoid closed cabinets, and note that corners can boost bass too much.
Does the HDMI cable matter?
A well-made cable that supports the features you need helps avoid dropouts. If you have problems, try another cable and check the soundbar and TV manuals for requirements.
Can I connect a soundbar to an older TV?
Usually yes, using optical or analog connections if the soundbar has matching inputs. You may not get the same format support as with HDMI, so check the listing.
Is eARC worth it for a soundbar?
It matters when both your TV and soundbar support eARC and you play high-quality lossless or object-based audio. For streaming and everyday viewing, regular ARC is usually enough. Check both manuals, because if one device lacks eARC the connection falls back to ARC.
Should I connect my game console to the TV or the soundbar?
Connecting to the TV is simplest, with audio returned through ARC. Connecting to the soundbar can preserve more audio formats but only if the bar passes video features such as high refresh rates and HDR. Check the specifications of both devices.
Why does my soundbar turn off by itself?
Many soundbars have an auto-standby feature that powers down after a period without a signal. HDMI CEC can also turn the bar off along with the TV. Check the settings for auto power off, and confirm the cable and port are secure.
Can I mount a soundbar under a wall-mounted TV?
Often yes, using the bar’s bracket or a separate shelf. Check the weight rating, use proper anchors or studs, and follow the manuals. Leave a gap so the bar does not block the TV remote sensor or picture. Hire a professional if unsure.
Why is my soundbar volume low on some apps?
Different apps and sources send audio at different levels, and some formats are quieter. Look for auto-volume or loudness settings on the TV and bar, set the audio format to automatic and check the app’s own sound options.
Bottom Line
Use HDMI ARC or eARC when you can and optical as a fallback.
More Soundbar Guides
- Best Soundbars
- Best Dolby Atmos Soundbars
- Best Soundbars Under $100
- Best Soundbars Under $200
- Best Soundbars Under $300
- Best Soundbars Under $500
- Best 5.1 Soundbars
- Best 2.1 Soundbars
- Best Soundbars with Wireless Subwoofer
- Best PC and Desktop Soundbars
- Best Gaming Soundbars
- Best Mini and Small Soundbars
- All soundbar guides
Related Guides
- 6 Best Soundbar Wall Mounts and Brackets: Under $30 (2026)
- 6 Best Soundbar Cables: HDMI ARC/eARC and Optical (2026)
- Soundbar Buying Guide: Channels, Atmos, Subwoofer, eARC (2026)
- 6 Best Soundbars for TV: Samsung, Philips, TCL, Polk (2026)
- 7 Best Dolby Atmos Soundbars: TCL, Samsung, Philips, Sonos (2026)


