A 4×6 label is four inches wide and six inches tall, the shape most shipping tools use for parcel labels. The numbers are only part of the story: the printable area, the gap between labels and the roll core all affect whether a label prints correctly. This guide walks through what each term means, how to set up a printer so the size matches the stock, and what to look at when a label comes out shifted, shrunk or blank in the wrong place.

Reading the Size
Label sizes are written as width by height. In “4×6” the first number is across the roll and the second is along the feed direction. Some makers list sizes in millimeters, so convert carefully and rely on the stock maker’s sheet for exact dimensions. For reference, 4 by 6 inches works out to roughly 101.6 by 152.4 millimeters, which is why a metric sheet may show numbers that look slightly different from what you expected.
Width and height can also be confusing because a label can be loaded in portrait or landscape. The roll always feeds the same way, but the layout inside the driver can be rotated. If a design looks sideways on the label, the rotation setting is a better first suspect than the stock itself.
In this guide
Terms You Will See
- Label width: the sticky label across the liner. The liner may be slightly wider than the label.
- Label height: the length of each label along the roll.
- Gap: the space between two labels on the liner. Printers use it to find where the next label begins.
- Printable area: the part of the label where the printer can place ink or heat. Edges are often left blank.
- Core: the cardboard tube in the middle of the roll, which must fit the roll holder.
- Outside diameter: the size of the full roll, limited by the printer’s roll space.
- Liner: the backing sheet the labels sit on.
- Feed direction: the way the roll moves through the printer.
- Calibration: a routine where the printer measures label length and gap.
- Offset: a small shift of the print position, left or right and up or down.
- Continuous stock: a roll with no gaps, cut to length by the user or printer.
Where Size Settings Go Wrong
- The page size in the driver differs from the label, so the print shifts or is cut off.
- The sensor does not match the stock type, such as gap versus continuous stock.
- A shipping tool outputs a different layout, for example a letter-sized page with a label in one corner.
- The label stock has been loaded off-center, so one side lands beyond the edge.
Common Label Sizes by Job
| Job | Typical size idea |
|---|---|
| Parcel shipping label | 4×6, if your carrier accepts it |
| Return or packing slip label | Smaller than 4×6, to fit on a pouch |
| Shelf and bin label | Small, sized to the shelf edge |
| Product label | Sized to the product surface |
Always check the carrier’s current instructions for required label sizes and placement.
A Quick Setup Routine
- Read the size on the stock maker sheet and note the width, height and gap.
- Open the printer driver or settings and enter those exact values.
- Choose the sensor type that matches the stock.
- Print one label and hold it against an unprinted label to compare the edges.
- Adjust offsets only after the size and sensor settings are correct.
Worked Walkthrough: Setting Up a New Roll
Here is a full pass through a new roll, using invented example values only. Suppose the stock sheet says the label is 4.00 inches wide, 6.00 inches tall, with a gap of 0.12 inches. These numbers are made up to show the steps; use the figures printed on your own sheet.
- Load the roll. Open the cover, seat the core on the holder and thread the liner under the guides so the labels face up. Slide the guides until they touch the liner edges without squeezing it.
- Let the printer learn the stock. Many printers have a calibration or feed routine that measures the gap. Follow the maker’s manual for the exact button sequence.
- Set the paper size in the driver. Create a custom size of 4.00 by 6.00 inches and save it under a clear name so you do not have to retype it.
- Set margins to zero or the minimum. Extra margins shrink the live area and can push content off the label.
- Check the scale. Select actual size or 100 percent, never fit to page.
- Print a sample label from the same program you use every day, not only from the driver’s own sample page, since the program may add its own page setup.
- Compare. Lay the printed label over a blank one. The edges should line up, and no text or barcode should touch the border.
Common Scenarios
The label prints in one corner of a big page
The shipping tool is sending a full sheet layout. Look in its print dialog for a label format option, then choose the 4×6 option and match it in the driver.
Every second label is blank
The printer is probably losing track of where one label ends. Re-run the stock calibration and confirm the sensor mode matches gap labels.
A new roll is slightly different from the old one
Different makers can use different gap sizes and liner widths even on the same nominal size. Re-enter the values from the new sheet rather than assuming they carried over.
The barcode looks squashed
Scaling is usually on. Turn off shrink-to-fit and confirm the driver size is the same as the label.
Quick Troubleshooting
| Symptom | Likely cause | What to try |
|---|---|---|
| Text cut off on one side | Stock loaded off-center or guides too loose | Reseat the roll and snug the guides |
| Print drifts down each label | Wrong height or sensor mode | Re-enter height and recalibrate |
| Label prints very small | Scaling or letter page size | Use actual size and a 4×6 page |
| Blank label between prints | Gap not detected | Run the stock sensing routine |
| Faded strip on one edge | Roll narrower than print head width | Check the manual for width settings |
Mistakes to Avoid
- Trusting the name alone. “4×6” is a nominal size, and liner width, gap and edge margins differ between makers. The stock sheet is the source of truth.
- Adjusting offsets first. Offsets hide a wrong size for a while but break again on the next roll.
- Letting the driver choose a default page. Many drivers default to letter or A4, which causes the corner problem described above.
- Skipping the comparison. A label that looks fine on screen can still sit too close to an edge for a scanner or carrier to read.
Care and Upkeep Over Time
Keep unused rolls in their wrapping, away from heat, sunlight and damp, since adhesive and coating can change with conditions. Wipe the platen roller and print head with the cleaning method given in the printer manual when output becomes uneven. Save your custom size profile and note which stock it belongs to, so a new roll with a different gap gets its own profile instead of overwriting the old one.
Direct Thermal or Thermal Transfer
Before you buy a roll of 4×6 labels, find out how your printer makes an image. The two common technologies need different stock, and buying the wrong one is a frequent reason a roll turns out blank or faint.
Direct thermal
A direct thermal printer heats a coated label so the coating darkens. There is no ribbon or ink. This is the usual design in desktop shipping label printers. The labels are convenient and cost-effective for short-term use, such as parcels that will be delivered in days. The tradeoff is that the coating reacts to heat, sunlight, and sometimes friction, so a label left on a hot dashboard or in a sunny window can darken or fade over time. Direct thermal stock is not intended for archival records.
Thermal transfer
A thermal transfer printer melts wax, resin, or a blend from a ribbon onto the label. These printers can print on a wider range of materials, including paper, synthetic films, and tags, and the image generally resists heat, smudging, and fading better than direct thermal. The cost is an extra consumable, the ribbon, and a more involved loading routine. If your printer manual mentions a ribbon, you probably have a transfer-capable machine. If it has none, buy direct thermal labels.
Many printers support only one mode, and some support both. Your manual or the manufacturer’s specification page lists which stock type to buy. If a label roll is described as direct thermal and your printer expects ribbon-based transfer media, it may print nothing visible even though the feed looks normal.
Stock Details Beyond Width and Height
Two rolls that are both labeled 4×6 can still behave differently in your printer. Compare the following specifications on the product listing or box.
- Core diameter: the cardboard tube in the center. Common cores are around one inch and three inches, and printers hold only certain sizes. Some printers have adapters or spindles for different cores. Check the manual.
- Outside roll diameter: a bigger roll holds more labels but must physically fit the printer’s roll compartment or an external holder.
- Labels per roll: this varies by stock and diameter, from a few hundred to several hundred more. Compare the count rather than assuming.
- Roll or fanfold: some printers take rolls, others take fanfold stacks that sit behind the printer. Fanfold labels are connected by perforations or a narrow web, and the printer must be set up for that style.
- Gap or mark: roll labels usually have a small gap between labels that a sensor detects. Some stock uses a black mark on the back, and the printer must be set to read marks instead of gaps.
Adhesive and surface
Standard permanent adhesive suits most cardboard boxes and poly mailers. Smooth plastic bags, cold or damp surfaces, and textured boxes can need a stronger or a freezer-grade adhesive. Removable adhesive exists for items you may reposition. If the label curls at the corners soon after you apply it, a stronger adhesive or a cleaner, dry surface is the first thing to look at. Wipe dust away and press firmly from the center out.
Planning the Layout of a 4×6 Label
Labels from carriers and shipping platforms arrive pre-formatted, but if you design your own for inventory bins, product tags, or warehouse locations, the size gives you a surprising amount of room: 24 square inches, less the margins.
Margins and safe area
Keep important content a short distance from the edges, often an eighth of an inch or more, since small shifts during feed and slight variation in roll position can clip text at the boundary. Your printer’s documentation may list a non-printable zone. Keep text and barcodes outside it.
Type size and readability
Text for sorting should be large enough to read at arm’s length. For addresses, many labels use somewhere around 10 to 12 point type at 203 dots per inch printers and a bit smaller on higher resolution units, but readability matters more than a fixed number. Avoid very thin fonts, which can break up at lower resolutions.
Barcodes
Barcodes depend on quiet space around them and clean bars. Print them at the size the standard or your carrier specifies rather than shrinking them to fit, and leave blank margins on either side. If a scanner struggles, increase the print darkness a bit and reduce the speed, then test again. Also avoid placing a barcode across a fold, corner, or seam when you stick it down.
| Common use | Typical content | Layout tip |
|---|---|---|
| Parcel shipping | Address, tracking barcode, service marks | Print the carrier’s file at 100 percent scale |
| Warehouse bin or shelf | Large code, short description | Use bold, high-contrast type |
| Product or pallet tag | SKU, batch, barcode | Leave a blank strip for hand notes |
| Return label | Return address, barcode | Confirm the barcode scans before printing a batch |
Getting the Printer Driver and App to Agree
Most print problems come from three layers disagreeing about the page: the file you are printing, the application’s print dialog, and the printer driver. Match all three to the same size.
- In the file or shipping platform, choose a 4×6 or 4 by 6 inch label format if one is offered. Some sites offer a PDF that is already that size.
- In the application print dialog, select the label printer, choose the paper size matching the label, and set scaling to actual size or 100 percent. Options such as fit to page or shrink to fit are a common source of undersized labels.
- In the printer driver or preferences, define a custom paper size of 4 by 6 inches if it is not already listed, and select the correct media type: labels with gaps, continuous, or marks.
- Set the orientation to match the file. A portrait file printed in landscape may rotate or clip.
- Print a single label as a test before sending a batch.
When you move to a different computer or reinstall the driver, the custom size is not always saved, so check it again. Some printers also keep their own internal media setting, adjustable from the front panel or a utility, that can override the computer.
Cost, Waste, and Stocking Habits
Label rolls are consumables, so a little planning prevents last-minute trouble. Rather than quoting prices that change often, here are ways to compare options sensibly.
- Compare cost per label, not cost per roll, by dividing the price by the label count on the listing.
- Bulk packs usually lower the per-label cost, but only buy a quantity you will use before heat or humidity affects the stock. Check the maker’s storage guidance.
- Buy one or two sample rolls of a new brand before committing to a large case, since sensor and adhesive differences can show up only in your printer.
- Keep a spare roll on hand so a surprise stockout does not stop shipments.
- If you ship low volume, a small starter pack avoids wasting money on labels that sit for a year.

Reducing waste
Every time a roll is loaded incorrectly or calibrated poorly, several labels are usually wasted feeding blank. Run the printer’s calibration or media sensing function after a roll change, keep the media guides snug against the roll edge, and make sure the label path is free of dust and adhesive residue. A cotton swab with the cleaning solution the maker recommends, used with the printer powered off, can clear residue from the print head and rollers. Let it dry before use.
Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
Why This Size Became the Standard: The Practical Logic Behind It
Standards rarely win because they are perfect; they win because they are good enough for almost everyone and because everyone else has already adopted them. The 4×6 label, four inches wide by six inches long, sits in that sweet spot for parcel shipping. It is large enough to hold a complete shipping layout, with the destination address in readable type, the return address, service information and a full-size scannable code with its quiet margins, without crowding. It is small enough to sit flat on the great majority of parcels people actually send, from shoebox-sized cartons upward. And because carriers, platforms, printer makers and stock producers all converged on it, every part of the system, templates, printer widths, roll sizes and software defaults, assumes it first and other sizes second.
That convergence feeds itself. A new seller adopts the size because the platform issues layouts in it. A printer maker designs around it because sellers use it. A stock producer makes it in every material and adhesive because printers accept it. Each adoption makes the next one easier, which is why asking whether a slightly different size might be marginally better misses the point: the value of the standard lies in the ecosystem, the ready templates, the certain compatibility and the shared knowledge when something goes wrong. When a 4×6 label misprints, a thousand other users have seen the same symptom and the fix is well known.
Checking the numbers yourself: conversions you can verify
You do not need to take the size on trust, because the arithmetic is simple and checkable with any ruler or converter. Four inches is 101.6 millimetres, and six inches is 152.4 millimetres, which is why the same label is often described in metric as roughly 100 by 150 millimetres. The small difference between the exact conversion and the rounded metric name matters when you set sizes in software: enter the size your printer and platform expect, in the units they display, rather than a converted approximation, and confirm with a test print measured against a ruler.
Area gives another self-check. A 4×6 label covers 24 square inches. A common smaller address label covers only a fraction of that, which is why a full shipping layout cannot shrink onto one without becoming unreadable, and why the code alone on a shipping layout, with its required quiet zone, claims a noticeable share of the label. If you ever wonder whether a layout can move to smaller stock, compare areas and then try a test print at full scale: the eye and a phone scan will settle in seconds what arithmetic suggests.
Scale percentages are the third check, and the one that saves the most parcels. Printing a 4×6 layout at full scale means the printed result measures four by six inches. If your test print measures noticeably less, some setting, fit to page, shrink to printable area, or a wrong paper size in the driver, has scaled it down, and the code has shrunk with it. Measure the test print before judging anything else; a ruler across a printed label is the fastest diagnostic in all of label printing, and it requires no technical knowledge at all.
How the standard shape shapes the layout
The portrait rectangle of a 4×6 label quietly organises the information on it. The destination address takes the prominent middle ground in the largest type, because that is what humans and machines need first. The return address sits smaller, usually toward the top. The code occupies a generous block, often toward the lower portion, with clear space around it so scanners can isolate it. Service marks and routing elements fill the remaining zones in positions regular users of a carrier come to recognise. When you receive a parcel, you are reading the result of that shared geography, which is why labels from different senders still feel familiar.
Understanding the geography helps you place labels well. The code block needs the flattest, cleanest area you can give it, and nothing, tape edges, box seams, marker pen, should cross it. The address block needs to stay complete and uncovered. When a parcel forces a compromise, protect the code first and the destination address second, and choose a bigger box rather than folding the label, because the layout was designed for a flat rectangle and every fold breaks the assumptions built into it.
When the standard is not the answer
Plenty of honest labeling work is not parcel shipping. Product labels, jar labels, address labels and organising labels all have their own sensible sizes, usually smaller, and forcing them into 4×6 would waste stock and look clumsy. Very small parcels may carry a carrier-issued alternative layout where the service offers one. The standard governs the mainstream shipping case; it does not demote every other size to a mistake. The error to avoid is the reverse: trying to make a full shipping layout live on stock meant for another job, or printing the standard layout at a reduced scale to suit a smaller roll you happened to have.
Stock up with the standard in mind. If you ship regularly, your main roll or sheet supply should be the size your carrier layouts assume, bought in the material your parcels need, with a small reserve so a busy week never finds the printer empty. Other sizes can live alongside for their own jobs, clearly separated and labeled, so that loading the wrong roll in a hurry becomes unlikely. Most 4×6 confusion, in the end, is not about the size at all; it is about settings and stock drifting apart, and a moment of checking before a batch keeps them together.
Settings That Must Agree: A Deeper Walk Through the Print Path
Nearly every 4×6 problem is a disagreement somewhere along the print path, the chain that runs from the file on your screen to the label in your hand. The chain has more links than most people realise, and each link holds a size or a scale setting of its own. This section walks the chain slowly, naming each link and the symptom it produces when it disagrees with the others, so that troubleshooting becomes a matter of locating the link rather than changing settings at random until something improves.
Link one: the document or platform view
The chain begins with the label as issued: a document with a defined page size, an image with defined dimensions, or a view inside a selling or carrier platform. Note what you are actually holding. A document carries its size inside it and should print true when later links respect it. An image carries pixel dimensions that different programs interpret at different physical sizes, which is why the same image file can print large from one program and small from another. A platform view may offer its own print button that behaves differently from printing the downloaded file. When a problem appears, return to this link and ask whether the source itself is the size you believe it is; printing a downloaded document file, where one is offered, removes an entire category of doubt.
Link two: the print dialogue and scaling
The print dialogue is where well-meaning defaults do the most damage. Options that fit content to a page, shrink oversized pages, or scale to a percentage exist for documents, and they are poison for labels, because a label is a measured object, not a page of text. The dialogue also holds a paper or media size selection that must name the label size you are using, not a letter or A4 page. Set scale to actual size or its equivalent wording, set the media size to the label, and then look for a preview: a truthful preview shows the layout filling the label shape in the right orientation, and a preview that shows a small label in a big white page is telling you the media size is wrong before you waste a single label.
Link three: the driver, the app and stored defaults
Behind the dialogue sits the driver or the printer app, with defaults of its own that can override what you just set. Many mysterious repeat failures, correct settings that will not stay correct, live here: a default media size stored in the driver, a preset saved under a friendly name, or an app that remembers the last job rather than your preference. Once you find a combination that works, save it deliberately as the default or as a named preset, and print a test after any software update, because updates are notorious for quietly resetting this link. If two computers or a computer and a phone share the printer, expect to set this link on each device; settings live on the device, not in the printer.
Link four: the printer own sense of the stock
The printer itself must know where one label ends and the next begins. Die-cut labels give it gaps or marks to sense; continuous stock asks it to trust the settings entirely. A printer that has lost its sense of the stock produces the wandering symptoms, labels starting progressively higher, every second label blank, printing split across a gap. Calibration, the routine described in the printer guidance, reteaches this link. Run it when you change stock type or size, when output starts to drift, and after moving the printer. It takes a moment, uses a few labels, and repairs a whole class of problems that no amount of software setting can touch.
Link five: the physical stock and how it is loaded
The last link is physical: the roll or stack itself. Stock loaded slightly skewed feeds increasingly crooked. A roll whose labels are a fraction different from the size the settings expect produces drift that looks electronic but is mechanical. Stock stored badly, curled, dusty or damp at the edges, feeds unevenly and prints unevenly. When output degrades gradually over a roll, suspect this link; when it fails suddenly after a change, suspect the link you just changed. That single diagnostic habit, sudden means settings, gradual means physical, resolves most troubleshooting sessions in minutes instead of afternoons.
A reference print that keeps the whole chain honest
End by making the chain prove itself. Keep one known-good label, printed when everything agreed, with a note of the settings that produced it: the source file type, the dialogue choices, the driver preset name and the stock description. When anything changes, print one test and hold it against the reference. Differences in size, position or density point at the link responsible far faster than memory does. The reference label costs nothing, lives in the front of your stock storage, and is the closest thing label printing has to a control experiment. Most long-term printing happiness is built from exactly such small, boring, repeatable checks.
Buying and Storing 4×6 Stock Without the Usual Waste
The standard size makes buying simple, but simple is not the same as automatic. Stock varies in material, adhesive, format and quality, and the wrong buying habits produce the two classic cupboards: one full of labels that do not suit the work, and an empty space where the everyday roll should be during the busiest week of the year. This section sets out a calm stock system for the size, built around knowing your real consumption and your real surfaces.
Know your surfaces before your quantities
List the parcels you actually send: the box types, mailers and any awkward regulars. Stock must stick to all of them, in the conditions they travel through. A general-purpose adhesive on a standard material covers the mainstream honestly. Special cases, parcels stored cold, items shipped in damp seasons, very rough recycled cardboard, deserve a deliberate stock choice rather than hope. Buy a small quantity of any new stock first and test it on your real parcels, including leaving a labeled parcel overnight and checking the edges in the morning. A stock that passes your own parcels can then be bought with confidence in the quantity your rhythm needs.
Rolls, fanfold and sheets: choosing the format you will live with
Rolls suit a dedicated printer and a steady rhythm: they load fast, store compactly and present labels in perfect order. Fanfold stacks feed the same printers in some setups and sit neatly behind the machine, trading a little storage footprint for very long uninterrupted runs. Sheets suit a general printer and an occasional rhythm, at the cost of part-used sheet management. The format decision should follow the printer and the rhythm you already have, not a bulk offer. A bargain on the wrong format is not a bargain; it is a slow leak of money and patience every time you print.
Whatever the format, store stock flat or as designed, away from heat, damp and direct sunlight, and keep it in its wrapping until it is loaded. Heat and light age thermal surfaces before they are ever printed, and damp warps sheets and weakens adhesive. The stock cupboard should be as boring as the reference label system described earlier in this guide: each type in its own labelled place, the everyday stock in front, the reorder point marked where you can see it. When the reserve roll comes out, that is the reorder moment, not when the printer runs dry mid-batch.
Reading a stock description like a professional
Stock listings compress a lot into a few terms, and reading them slowly once is a skill that pays forever. Size first, in the units your setup uses, with width and length in the order the seller states, which is not universal. Format second: roll, fanfold or sheet, and for rolls, the core and the way the labels wind, since a printer can only accept what physically fits and feeds. Material and adhesive third, matched to your surfaces as above. Compatibility last and most carefully: a stock described for a printing method you do not use, direct thermal versus thermal transfer being the classic confusion, will not work in your machine however perfect its size. Four slow checks against the listing, made once per order, prevent the entire genre of disappointment that arrives in a box of almost-right labels.
Teaching someone else your 4×6 setup
The true test of a working setup is whether another person can use it in your absence. A partner covering a dispatch day, a family member posting one parcel, a new helper in a small business: each of them meets your system exactly as you left it, and every undocumented assumption becomes their mistake. Document the few things that matter, in the place where the work happens. Which stock is the everyday stock, and where the spare lives. Which preset or setting name produces a correct label, stated exactly as it appears on screen. What a correct label looks like, with your reference print pinned or stored right there for comparison. And what to do when a print comes out wrong: measure it, check the stock against the setting, print one test, and stop rather than experimenting with a batch. Four short notes, written once, convert your private knowledge into a system, and they protect your parcels on the days you are ill, travelling or simply busy elsewhere. If writing those notes reveals a step you cannot explain simply, that step is a weakness in the setup itself, and simplifying it helps you every day, not just your stand-in. A standard size deserves a standard routine, and a routine deserves to be written down where the labels are printed.
There is a confidence dividend to a written routine that is easy to underestimate. When the setup lives in notes and a reference print rather than in one person memory, dispatch stops depending on mood, memory or who is available, and the error rate settles at the level the routine was designed for. Parcels go out correctly on ordinary days and on chaotic ones, which is when correctness is worth most. If this guide leaves you with a single project, let it be that one: measure a test print, pin up the reference, write the four notes, and enjoy how uninteresting your label printing becomes from that day forward. Uninteresting, in a shipping routine, is the highest compliment there is.
And if the stand-in still manages to produce a bad label, treat it as information rather than failure: the step they stumbled on is the step your notes did not make clear enough, and improving that one line improves the system for everyone, including you on your next tired evening. Systems get robust exactly this way, one clarified line at a time, until the day nobody can remember the setup ever being difficult at all.
FAQ
Is 4×6 the same as A6?
They are close but not identical. A6 is a metric size of 105 by 148 millimeters, while 4×6 is about 101.6 by 152.4 millimeters. Check the dimensions on your stock sheet, and set the driver to match the stock you actually use.
Why does my label print too small?
Shrink-to-fit or scale settings are often on. Turn scaling off and use actual size. Also confirm the page size is 4×6 and not letter, because a letter page shrinks a label layout to fit.
Do I need to calibrate every time I change rolls?
It is a good habit when the new roll comes from a different maker or has a different gap. If the stock is identical, many printers keep working without it, but a quick feed check confirms alignment.
Can I print a 4×6 label on a smaller label size?
Only if the layout is scaled down, which can make barcodes harder to scan. Check what your carrier currently accepts and use the size it requires.
What does printable area mean for my design?
It is the zone where the printer can mark the label. Keep text and barcodes comfortably inside it, away from the edges, so small shifts do not clip them.
What is the difference between direct thermal and thermal transfer labels?
Direct thermal labels have a heat-sensitive coating and need no ribbon, which suits short-term shipping labels. Thermal transfer prints by melting ribbon onto the label and generally lasts longer on more materials. Buy the type your printer’s manual says it supports.
Why is my 4×6 label printing blank?
Common causes include the wrong stock type for the printer, labels loaded upside down, a missing or incorrectly loaded ribbon on a transfer printer, or low darkness. Check the stock type, flip the roll if needed, and run the printer’s feed or test print to confirm.
What core size do 4×6 label rolls come in?
Rolls come with different core diameters, with around one inch and three inches both common. Your printer holds only certain cores, sometimes with adapters. Check the manual and the product listing before buying a roll.
Do thermal labels fade over time?
Direct thermal labels can darken or fade when exposed to heat, sunlight, or friction, so they suit short-term use. For longer life, a thermal transfer setup with suitable ribbon and stock is usually more durable, depending on the materials.
How do I print a shipping label at 100 percent scale?
In the print dialog, pick the 4 by 6 inch paper size, then choose actual size or 100 percent scaling instead of fit to page. Make sure the printer driver uses the same size, then print one test label.
Is a 100 by 150 millimetre label exactly the same as 4×6?
Nearly, but not exactly: four inches converts to 101.6 millimetres and six inches to 152.4 millimetres, so the metric name is a rounding. In practice the two are treated as the same label class, but in software you should select the size your printer and platform list, and confirm with a measured test print rather than assuming a converted value is identical.
Why do printers and software default to this size?
Because carrier shipping layouts are issued in it, so defaults follow demand. A printer that handles this size covers the mainstream shipping case, and software that assumes it matches the files most users print. Defaults are a starting point, though; if your work uses another size, set that as your default deliberately so every session begins from the right assumption.
Can I use 4×6 labels for things other than shipping?
Yes, for anything that benefits from a large label: storage boxes, shelf edges in a workshop, or clear labeling of bulky items. The size is generous for small items, where it can wrap or overwhelm, so match the label to the object. There is no rule reserving the size for parcels; it is simply the size the shipping system standardised on.
How can I tell if my label printed at the correct size?
Measure it. A correctly printed 4×6 label measures four inches by six inches, or the metric equivalent your stock specifies. If it measures smaller, look for a scaling setting, a fit-to-page option or a mismatched paper size in the driver or app. Fix the setting and reprint a single test label before continuing with a batch.
The Short Version
4×6 means width by height in inches, but gap, core and printable area also matter. Set the driver to the exact stock, turn off scaling and print one label to compare before running a batch. Confirm requirements with your carrier, and save a profile for each stock you use.

