Yes. A regular inkjet or laser printer can produce a shipping label that carriers accept, as long as the barcode is sharp and the label is the size the carrier asks for. A dedicated label printer is a convenience for frequent senders, not a requirement. This guide covers what a good result looks like, how to choose between paper and sheets, a full walkthrough and the usual causes of smudges and failed scans.

What Counts as a Good Result
Carriers scan the code automatically, so what matters is contrast and clarity. Look for these signs:
- Black bars on a white background, with no grey patches.
- No streaks, smears or missing lines through the code.
- The address is easy to read at arm’s length.
- The label is flat, with no creases across the code.
In this guide
Choosing the Media
You have two common choices, and neither is better in every case.
| Media | Good side | Weak side |
|---|---|---|
| Plain paper plus tape | Always on hand | Needs careful taping and trimming |
| Sticky label sheets | Peel and apply | Must match the printer type, inkjet or laser |
Use sheets marked for your printer type. Heat from a laser printer can damage stock that was made for inkjet use, so read the packaging.
Settings to Check
- Set the scale to actual size, not fit to page.
- Choose the paper type that matches what is in the tray.
- Choose a normal or higher quality mode if you see grey text; for inkjets, plain paper mode may smear on glossy sheets.
- Print one copy only and inspect it.
Common Problems
Streaks usually mean a dirty or dry printhead on an inkjet, or a worn drum or low toner on a laser. Run the cleaning routine in the printer menu. Smudging with inkjets often comes from handling the page before it dries, so give it a moment. Tiny lines across a barcode can stop it scanning, which is the one fault worth reprinting for.
Inkjet or Laser: Small Differences
Laser output tends to resist smearing once it leaves the printer, because the toner is fused with heat. Inkjet output can run if it gets wet, so keep it away from damp hands and wet packaging. Either type works for a single label. If you ship often and your pages keep smudging, a roll printer or a print service may suit you better, and the maker’s guide for your current printer will list the media it supports.
Whatever you use, keep spare paper and a stock of tape so a failed print never delays the parcel.
Worked Walkthrough: From Order to Taped Parcel
This sequence suits a single parcel printed on a household printer.
- Pack and weigh. Seal the box, then weigh and measure it. Enter the figures into your shipping account, as the carrier’s current instructions describe.
- Create the label. Choose the layout your account offers. A full page, a half page or a label-sized layout may all be available.
- Look over the file. Check that the address block and barcode are complete on screen, and that nothing is cut at the edges.
- Print one copy. Use actual size, the right paper type and normal or higher quality.
- Inspect. Hold the page at arm’s length. Look at the barcode closely for streaks, then read the address.
- Attach. For plain paper, cut around the label leaving a border. Place it flat on the largest face of the box and tape over the whole label, keeping tape off the barcode surface only if the carrier’s instructions say so; clear tape over the full label is common practice, but check the current guidance.
- Cover old marks. Remove or fully cover any old labels or addresses on the box.
- Keep the receipt. Save the tracking number and any receipt your account provides.
Common Scenarios
Printing an occasional return label
Plain paper and tape are usually fine. Print at actual size and tape it down fully so edges cannot lift.
Running out of ink or toner mid-job
Faint barcodes are a problem. If the print looks pale, replace the cartridge or toner before printing the label, or use a different printer for that job.
A small parcel with little flat area
Choose a layout that fits, or trim the label while keeping all required information and a border. Do not fold the label over an edge across the barcode.
Sending several parcels a week
A roll printer may save time. The maker’s guide and your account will list which printers and sizes work.
Quick Troubleshooting
| Symptom | Likely cause | What to try |
|---|---|---|
| White lines through the barcode | Clogged nozzles or low toner | Run the cleaning cycle and reprint |
| Label prints too small | Fit-to-page scaling | Set to actual size |
| Ink smears when touched | Wrong paper setting or wet handling | Let it dry, check the paper type |
| Label sheet jams | Curled or old sheets | Use fresh sheets and feed them as the manual describes |
| Barcode will not scan with a phone | Low contrast or damage | Reprint at higher quality and use a flat page |
Mistakes to Avoid
- Printing in draft or economy mode. Pale bars may fail to scan.
- Taping over the label unevenly. Wrinkles over the code cause misreads.
- Reusing a printed label. Each label is tied to one shipment and cannot be reused.
- Using the wrong sheet type. Inkjet sheets in a laser printer can melt or jam.
- Ignoring the carrier’s size notes. Check the carrier’s current instructions for sizes and placement.
Care and Upkeep Over Time
If a printer sits idle, inkjets can dry out, so run a short print now and then. Keep paper flat and dry in its wrapping. Clean the printer as its manual describes, and replace consumables when output gets pale. Keep a few sheets of the right label stock aside, so you are not caught out when a rush job turns up.
Choosing Between Printing at Home and Using a Service
Occasional senders usually do fine at home. The cost of ink or toner, the need to keep paper in stock and the time spent on cutting and taping are the trade-offs. If you send many parcels, or your printer struggles with barcodes, a roll printer or a local print counter can take the strain. Some carriers and shops also print labels from a code on your phone or a file you send them, so ask what your carrier currently offers. Whichever route you choose, keep the tracking number in a safe place until the parcel arrives.
Label Sizes and Layouts You Are Likely to See
Shipping labels come in a few common layouts, and knowing them helps you choose paper and settings that match the carrier’s expectations. Carriers and shipping platforms let you choose the format when you buy postage, so decide before you print.
Full-page and half-page formats
Many services default to a full letter-size page with the label in the top half or the top left. You can print this on plain paper, then cut or fold it to fit a package. Half-sheet self-adhesive paper holds two labels per page, so you can print one and keep the second half for later if the printer feeds it correctly. A full sheet is wasteful for one label, so the half-page option is a common middle ground.
Four-by-six inch format
The four-by-six inch label is the standard size for thermal label printers. Some shipping platforms also let you print this size on a regular printer by changing the page size in the print dialog. If your printer supports custom paper sizes or label stock, this can produce a neat, parcel-sized label without trimming. Test on plain paper first to check the layout.
Where the barcode needs room
Carrier scanners read the barcode or QR code on the label. It should be sharp, dark, and unbroken, with some blank space around it. Do not shrink the label below the size the service prints, because scanners can have trouble reading barcodes that have been scaled down too far. Print at 100 percent or actual size, and avoid options such as fit to page unless the platform tells you to use it.
Using the paperless option
Some carriers offer a printer-free option in which the sender shows a QR code at a drop-off location where staff print the label. If you do not have a printer, or if yours is out of ink, this option may be convenient. Availability and terms vary, so check with the carrier.
Print Quality: Resolution, Contrast, and Scan Reliability
The label must be readable by machines as well as people. A label that looks fine at a glance can fail at a sorting facility if the lines of the barcode are faded or smeared. A few checks on print quality prevent returned or delayed parcels.
Set the quality mode
Choose a normal or high quality print mode instead of draft or economy mode. Draft modes use less ink or toner and can produce thin, grayish lines that scan poorly. If your printer has a setting for plain paper or for label stock, select the one that matches what you loaded.
Check the barcode visually
Look at the barcode on the printed page. The bars should be solid black with sharp edges and no white streaks or blurry areas. If you see banding or streaks, run the printer cleaning routine described in its manual, check ink or toner levels, and reprint. Never tape over a barcode with wrinkled or cloudy tape that could cause glare.
Test with a phone scanner
Many phone cameras can scan barcodes or QR codes. Pointing your phone at the printed code is a quick way to see whether it reads. This is not a perfect test of carrier scanners, but if the phone struggles, a scanner probably will too.
Protecting the label on the parcel
Place the label flat on the largest surface of the package, away from edges, seams, and folds. Cover paper labels completely with clear packing tape, taking care that the tape is smooth and does not wrinkle over the barcode. If the parcel is likely to get wet, a clear plastic sleeve or label pouch can give additional protection.
Address Accuracy and Required Information
Even a perfect print will not help if the address is wrong. Most shipping errors come from typing mistakes, missing apartment numbers, or outdated information. Spend a minute checking before you pay for postage.
Use address validation
Many shipping platforms check addresses against postal databases and suggest corrections. Accept suggestions only after confirming they match what the recipient provided. If the system flags an address as not found, contact the recipient to confirm details instead of guessing.
Include everything that matters
Include the apartment, suite, or unit number, the full ZIP or postal code, and a phone number or email if the platform asks for one. For international parcels, additional details such as customs forms, content descriptions, and declared values are usually needed. Requirements vary by country and carrier, so check the current rules on the carrier’s website.
Remove or cover old labels
When reusing a box, remove or fully cover old labels and barcodes, including those on other sides. Old barcodes can confuse scanners and send a parcel to the wrong place. Use a thick marker or opaque tape to cover anything you cannot peel off.
Keep a record
Save the tracking number and a copy of the receipt or confirmation. If the package is delayed or lost, you will need these to file a claim or ask for help. Take a photo of the packed item and the label if the contents are valuable.
Cost, Supplies, and Environmental Considerations
Printing labels at home has costs beyond the postage itself. Thinking about supplies can help you decide how much to invest.
Ink, toner, and paper
Each label uses a small amount of ink or toner, but heavy use adds up. Laser printers usually have a lower cost per page for text-heavy labels, while inkjet cartridges can be more expensive per page. Prices change often, so compare current figures for your printer model. Plain paper plus tape is the cheapest option; adhesive label sheets cost more but save time.
Adhesive labels versus tape
Self-adhesive sheets stick without extra tape, though you may still want clear tape over the edges to protect the label in transit. Plain paper requires tape across the entire surface. If you use sheets with perforated halves, make sure the sheet is flat and unwrinkled in the printer to avoid jams.
Printer jams and sticky residue
Use label sheets designed for your type of printer, because heat in a laser printer can melt adhesives not rated for it. Do not reload sheets from which labels have been peeled, since exposed adhesive can gum up the rollers. If a sheet jams, turn off the printer and follow the manual for removing it.
Waste and recycling
Backing sheets from labels and used cartridges can be bulky. Check local rules for recycling paper and printer supplies. Reusing boxes and printing on the unused half of a page cuts waste as well as cost.
When a Thermal Label Printer Starts to Make Sense
A regular printer is fine for occasional shipping, but at higher volumes a dedicated thermal label printer may be worth considering. This section describes the tradeoffs in general terms.
How thermal printing differs
Thermal label printers use heat to darken special paper, so they need no ink or toner. They print four-by-six inch labels directly, with no cutting or taping of a full page. Labels are typically sold in rolls, and the cost per label is often low compared to ink and adhesive sheets, though you should check current prices.
Signs it may be time
Consider a thermal printer if you ship several parcels a week, if you waste a lot of paper, or if you find yourself frequently clearing jams and cleaning print heads on your regular machine. The decision depends on volume. For a few parcels a month, the added cost and shelf space may not pay off.
Compatibility and setup
Before buying, confirm that the printer works with the shipping platforms and carriers you use, and with your computer’s operating system. Check the roll size, whether it needs a specific brand of labels, and how it connects. Read the manufacturer instructions for setup and for cleaning the print head.

Keep the old printer as a backup
Even with a thermal printer, keeping a regular printer available gives you a fallback when supplies run out or a roll jams. Plain paper and clear tape work in a pinch.
Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
View Avery Shipping Labels 5164 on Amazon
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
Check Before You Print: Carrier Rules and Label Basics
Carriers decide what a usable label looks like, so the first stop is always the carrier’s own guidance. Pages change, and a quick check can save a returned parcel.
- Read the carrier’s current instructions for printing labels at home.
- Confirm the print size the carrier wants, and whether to print at full scale.
- Make sure the barcode area is clean, dark and free of creases.
- Print at the highest text and barcode quality your printer offers.
- Look over the address block to be certain it is complete and correct.
- Keep the tracking number somewhere safe, in case the label is damaged.
If the barcode looks faint or blurred, print it again rather than hoping it will scan.
Paper, Sticker Sheet or Tape: Choosing How to Attach
A printed label still has to stay on the parcel. This table compares common ways in general terms.
| Method | Strength | Watch for |
|---|---|---|
| Plain paper with clear tape over it | Easy and always available | Tape must cover the whole label but not wrinkle the barcode |
| Self-adhesive sheet labels | Neat and fast | Check that your printer accepts the sheet |
| Half-sheet labels | Less waste | Make sure the size matches the carrier’s needs |
| Pouch or sleeve | Protects the label from wet weather | Seal it so moisture stays out |
Place the label on the largest flat surface of the parcel, away from seams and edges. Remove or cover old labels so scanners read only the current one.
For items that need special handling, follow the carrier’s instructions for marking and packing.
Keep a few spare sheets and a roll of clear tape beside the printer, so a last minute parcel does not turn into a search around the house.
What Your Regular Printer Is Really Doing With a Label
A regular printer treats a shipping label as an ordinary page image, and that simple fact explains both why the method works and where it can stumble. The carrier or selling platform prepares a document, usually a fixed-layout file, and your printer’s job is to place that image on paper at the intended size. An inkjet lays tiny droplets of ink onto the surface, while a laser printer uses static charge and heat to fuse dry toner into the sheet. Both can produce a perfectly serviceable label. The risks are not in the basic idea but in the details around it: scaling that quietly shrinks the label, a paper path that creases the sheet, ink that smears while damp, or a low toner state that leaves the barcode pale in one corner.
Scaling deserves special attention because it is the most common silent failure. Print dialogs often offer a fit-to-page option that sounds harmless and is anything but, because a label reduced even slightly can still look fine to the eye while its barcode modules become narrower than the design intends. Sorting equipment reads barcodes by measuring the pattern of bars and spaces, and a shrunken or stretched pattern gives the reader less margin for error. Printing at actual size, with scaling switched off, and then measuring the printed label against the size named in the document is a thirty-second habit that prevents a surprising share of scanning trouble.
Inkjet behaviour on labels
Inkjet output is wet when it leaves the printer, so a label handled immediately can smear under a thumb or under packing tape pressed down too eagerly. Give the sheet a short rest before touching the printed area, and be aware that very absorbent paper can feather fine edges, making small text and barcode bars look slightly woolly. Standard settings suit most labels; the highest quality modes lay down more ink than a barcode needs and can actually soften edges. If your parcels travel in damp conditions, remember that many inkjet inks will run when wet, which is one reason the taping and protection advice elsewhere in this guide matters so much for inkjet users.
Laser behaviour on labels
Laser output leaves the printer dry and firmly fused, which makes it naturally resistant to casual smudging and light moisture. The laser’s challenges are different. The sheet passes through a hot fusing stage, so adhesive label sheets must be the type made for laser printers; the wrong sheet can soften, ooze adhesive inside the machine or peel a label off mid-path and wrap it around a roller. Plain paper through a laser is trouble-free, but once you move to self-adhesive sheets, the maker’s guidance for your printer type is not fine print to skip. Heat also means a sheet fed through repeatedly, for example when you print one label from a multi-label sheet across several sessions, can gradually curl or dry its adhesive, so partially used sheets deserve a flat, cool storage place and a realistic limit on reuse.
Making the Barcode the Priority
Everything else on a shipping label can be read by a patient human. The barcode cannot. It is read by machines moving parcels quickly, in mixed lighting, sometimes through tape or a pouch, so the label should be produced and handled with the barcode’s needs first. It needs strong contrast, meaning genuinely dark bars on a genuinely pale background. It needs its quiet zones, the blank margins around the pattern, left empty rather than cropped, written over or covered by a tape edge. It needs to sit flat, because a barcode wrapped over an edge or creased through its middle presents a distorted pattern that many readers will reject even though every bar is technically present.
A home check is easy and worthwhile. Most phones can scan the common label barcodes with a camera app or a free scanner, and while a phone is more forgiving than sorting equipment, a label your phone struggles with is a label worth reprinting. Scan in ordinary room light rather than under a bright lamp that flatters it, and scan after you have taped or pouched the label, not before, because glare from tape can turn a good print into a poor read. If the scan is instant and repeatable from a slight angle, you have done your part. If it hesitates, check darkness, scaling and flatness in that order before blaming the carrier’s systems.
Darkness and quality settings that actually help
When a barcode prints pale, the instinct is to select the highest quality mode and try again. Sometimes that helps, but check the simpler causes first: a low ink or toner state, an economy or draft mode left on from an earlier job, or a document that was itself generated in grey rather than black. A fresh cartridge state, normal quality mode and a document printed as a true black image will outperform a tired supply pushed through an extreme setting. Also look across the whole barcode rather than at its centre. Fading that affects one side only often points to a supply running low on that side or, in a laser printer, to a cartridge that benefits from being gently rocked to redistribute toner, following the maker’s instructions.
Paper Path, Sheets and the Small Mechanics of Feeding
Labels fail in the paper path more often than in the print settings. A sheet that enters slightly skewed will carry a label printed slightly rotated, and rotation that looks trivial on an address can tilt a barcode enough to matter. Use the paper guides in the tray, snug against the sheet without buckling it. Keep the stack modest rather than overfilled, fan sheets gently if they cling together in dry weather, and avoid mixing part-used adhesive sheets with plain paper in the same tray, because the printer may pull the wrong sheet at the worst moment. For a single important label, feeding one sheet through the manual or rear slot, where your printer offers one, often gives the straightest path and the flattest result.
Adhesive sheets deserve their own routine. Feed them in the direction the packaging recommends, print the labels in an order that keeps the sheet balanced rather than stripping all the labels from one corner first, and never put a sheet through with a label already missing from the leading edge, because exposed adhesive can catch inside the machine. If a label does peel inside the printer, switch off and follow the maker’s clearing guidance rather than pulling blindly against the path, which can tear the label and leave fragments and adhesive where the next sheets pass. A printer that has suffered an adhesive incident often shows it afterwards as faint marks or recurring jams until the path is properly cleaned.
Plain paper plus tape, done properly
The plain-paper method remains entirely respectable when it is done with care. Cut the label out with straight edges and a margin of blank paper around the barcode’s quiet zones. Lay it flat on the largest smooth face of the parcel, away from seams and edges. Cover it fully with clear packing tape, applied in smooth strips that do not overlap across the barcode itself, because each tape edge crossing the pattern adds a line the reader must ignore. Press the tape down from the centre outward so no bubble sits over the bars. Alternatively, a clear document pouch stuck to the parcel holds the paper label flat, protected and readable, and pouches are forgiving for people who send parcels in wet weather or who dislike taping directly over print.
Checking the Label Against the Booking, Every Time
A beautifully printed label for the wrong booking is still the wrong label. Before anything is stuck down, compare the printed piece against the order or booking on screen: recipient name, address lines, postcode, service marks and any reference the carrier prints. Parcels are most often mislabelled in busy households and small packing areas where two orders are open at once, so a calm sequence helps. Print one label, attach it, and close that order before printing the next. Keep printed labels in the order they came off the printer if you must batch them, and never leave a small pile of similar-looking labels beside several open boxes without a system that ties each label to its contents.
Weight and size honesty belongs in this check too. A label is bought for a parcel of a stated weight and dimensions, and a regular printer will happily print it whether the real parcel matches or not. If you have added heavier contents, swapped to a larger box or combined orders since booking, the label may no longer describe the parcel, and the time to discover that is at your table, not at the counter or through a later adjustment notice. Reweigh, remeasure and rebook when the parcel has changed in a way the carrier would care about, following the carrier’s own current guidance for how such changes are handled.
What to do when the print and the parcel disagree
If you catch a mismatch before handover, the safe pattern is consistent across carriers even though the exact steps differ: do not use the label, void or cancel it through the channel where you bought it if that option is offered, and create a correct label for the parcel as it actually is. Keep the voided sheet out of the packing area so it cannot be picked up in error later, ideally marked clearly across its face. Where the route for voiding or refunds is unclear, ask the carrier or the platform that sold the label rather than assuming an unused label simply lapses, because the handling of unused labels is set by the seller’s terms and not by anything your printer does.
A Weekly Sender’s Routine on a Regular Printer
People who send a handful of parcels every week sit in the middle ground where a regular printer still works well, provided the routine is tidy. Keep a small dedicated stock: plain paper or the adhesive sheets your printer handles happily, clear tape or pouches, and a spare ink or toner supply bought before the current one runs out rather than after. Running dry mid-label is the classic regular-printer failure, and it always seems to happen with a parcel already sealed. A spare supply on the shelf converts that crisis into a two-minute pause.
Settle on one label format and one print preset, and save both. Most wasted time and most misprints come from re-deciding settings at every session: paper size rediscovered, scaling toggled, the wrong tray selected. A saved preset that names the paper size, actual-size printing and the tray you use removes that friction. Keep a test sheet habit as well. After any change, such as a new paper type, a replaced cartridge or a software update, print one label and scan its barcode with your phone before printing the session’s real labels. Software updates in particular can quietly reset a scaling preference, and the test sheet is how you catch that on a spare page rather than on a customer’s parcel.
Keeping records without extra effort
Save the label document or a photograph of each attached label alongside the order record. When a parcel is queried, the tracking reference, the exact address as printed and the service used are the details every carrier conversation begins with, and they are far easier to supply from a saved copy than from memory. A photograph taken at the packing table also settles most disagreements about whether an old label was left visible on a reused box or whether the label sat flat. This takes seconds per parcel and repays itself the initial time anything goes astray.
Knowing When the Regular Printer Has Done Enough
The honest test is friction, not fashion. If you print a label now and then, the regular printer you already own is the economical and sensible tool, and the advice in this guide is all you need. The balance shifts when label printing becomes a daily interruption: sheets wasted on single labels, ink costs that sting, time lost to taping and trimming, or a growing pile of parcels waiting on a shared household printer. At that point a dedicated thermal label printer earns its place by printing the exact label size, one at a time, with no ink and no trimming. Many sellers keep both, using the thermal machine for routine labels and the regular printer as the backup that saves the day when anything else fails.
Whichever stage you are at, judge your current setup by outcomes over a month rather than by one bad afternoon. Count the labels that needed reprinting, the parcels queried for scanning problems and the sessions interrupted by supplies. If those numbers are near zero, your regular printer is not a compromise at all; it is simply the right tool being used well. If they keep recurring, the problem is rarely your care or effort, and upgrading the tool will do more than trying ever harder with the wrong one.
Printing Labels From Phones and Shared Computers
Many labels now begin on a phone, and printing from a phone to a regular printer introduces its own quiet traps. Phone print dialogs tend to hide the scaling control, and some apps hand the printer a photograph-style rendering of the document rather than the document itself, which can soften the barcode. Where you can, open the label document itself rather than a screenshot of it, choose the printer deliberately instead of accepting whichever device the phone suggests, and check the preview’s proportions against the stated label size before printing. If the phone route keeps producing soft or shrunken labels, move that one step to a computer for label printing while keeping the phone for everything else in the order process. There is no prize for printing from the smallest screen if the result needs reprinting.
Shared household and office printers add a different risk: someone else’s job sitting in the queue or their settings left active. A label printed on coloured paper left in the tray, or on a transparency setting left over from another task, wastes the label and sometimes the booking’s calm entirely. A quick glance at the tray and the on-screen settings before you print, and collecting your label promptly so it is not shuffled into someone else’s paperwork, are small courtesies that prevent the most avoidable misprints. In a busy shared space, naming your saved preset clearly also helps the next person leave it alone.
When the document itself is the problem
Occasionally every setting is right and the label still prints badly, because the document supplied is faint, distorted or built at the wrong size. Regenerating the label from the carrier or platform, rather than repeatedly reprinting the same flawed file, is the correct response. A fresh copy replaces a corrupted download and reflects any correction you made to the address or service in the meantime. If a regenerated document still looks wrong in preview, that is a question for the platform or carrier that issued it, and it is better asked before the parcel leaves than explained afterwards with a parcel already in the network carrying a label nobody can read.
Recovering Gracefully When a Print Goes Wrong Mid-Session
Even a tidy routine meets a bad afternoon: a cartridge fades halfway through a label, a sheet feeds crooked, or the computer restarts with jobs still queued. The recovery pattern matters more than the mishap. Stop and look at the physical sheet first, because the sheet tells you whether anything usable was printed and whether a duplicate may already exist. Check the print queue before pressing print again, since a job that looked lost often reappears when the printer wakes, and two good copies of one label invite the duplicate-parcel mistake. If a label is spoiled, mark it across its face immediately or destroy it, so the session’s tidying-up cannot resurrect it onto the wrong box. Then fix the cause, low supply, skewed feed or a setting changed by an update, print one test label, scan it, and only then resume the real work. Sessions recovered this way lose a few minutes. Sessions recovered by pressing print repeatedly lose track of which label belongs to which parcel, and that confusion is the one error in home label printing that genuinely costs money.
FAQ
Do I need a full sheet for one label?
Not always. Some accounts offer a half-page layout, and a spare half can sometimes be used again. Check what your printer accepts before reusing paper.
Can I cut a label out of the page?
Often yes, but keep the border around the code and follow the carrier’s current instructions about the label’s size.
Is black and white enough?
Yes, labels are normally black on white. Colour is not needed, and a single-colour print is often the most reliable.
Can I print the label from my phone?
If your printer supports it, yes. Make sure the phone’s print dialog uses actual size, then inspect the result like any other print.
Should I laminate the label?
It is not usually needed. Clear tape over the whole label protects it from rubbing and damp. Follow the carrier’s current instructions on placement.
What size should a shipping label be when printed at home?
It depends on the carrier and platform. Many offer a full letter page, a half sheet, or a four-by-six inch format. Print at actual size, with no fit-to-page scaling, so the barcode keeps its intended dimensions. Check the platform instructions to see which formats it recommends for regular printers.
Why is my shipping label barcode not scanning?
Common causes are faded or streaky printing, a barcode scaled too small, wrinkled tape over the code, or a damaged package surface. Reprint in normal or high quality, check ink or toner, clean the print heads if needed, and apply smooth clear tape that does not wrinkle over the barcode.
Do I need to cover the label with tape?
Covering a paper label with clear packing tape helps protect it from moisture, rubbing, and smudging, especially with inkjet ink. Make sure the tape is smooth and clear so the barcode is not blocked by glare or wrinkles. Self-adhesive labels may still benefit from tape over the edges.
What should I do with an old shipping label on a reused box?
Remove it completely or cover it with thick opaque tape or a marker so no old barcode can be scanned. Check every side of the box, including the bottom and flaps. Old barcodes can confuse sorting machines and send the parcel to the wrong address.
Can I print a label without a printer?
Some carriers offer a printer-free option in which you get a QR code on your phone and show it at a drop-off location where staff print the label. Availability and terms vary by carrier and location, so check the carrier’s website before relying on it.
The Short Version
A regular printer can do the job when the barcode is crisp, the size is right and the label is flat and fully attached. Print one copy, inspect it, and reprint if anything looks streaked. Check the carrier’s current instructions for size and placement.

